Effect Control - Yamaha SY99 Owner's Manual

COMMON DATA / EFFECT SET
Summary: Specify how two selected parameters
of the effect unit will be controlled in realtime.
Procedure:
From: Effect Set job directory
Select: job 05:Effect Control
Specify: the parameters to be controlled and the
controller for each
Param (see below): Select any two of the fol-
lowing effect parameters to be controlled. The
selected controller will affect ...EF1 Par 1-10: a
parameter 1-10 of effect unit 1.
EF1 Level1/2: the effect level 1 or 2 of effect unit
1.
EF2 Mix Level: the amount of Effect 2 that is
present in the effect chain. (This parameter is
meaningful only when the Effect Mode is Serial.)
EF2 Par1-10: a parameter 1-10 of effect unit 2.
EP2 Level1/2: the effect level 1 or 2 of effect unit
2.
Out1/2 w:d: the wet:dry balance of output 1 or 2.
Cnt1 MIN: the percentage of a parameter's full
range that will result when a controller moves to
its minimum position (see
Cnt1 MAX: the percentage of a parameter's full
range that will result when a controller moves to
its maximum position (see
LFO Wave: the waveform of the Effect LFO
(see
).
LFO Spd: Control the speed of the Effect LFO
(see
LFO Dly: Control the delay time of the Effect
LFO (see
LFO Phs: Control the initial phase of the Effect
LFO (see
Ctrl# & Device (001...120, Aftertouch, Velocity,
Key Scale, LFO): Select the control source
which will affect the selected effect param-
eter.001 Modulation ... 120 Non-Assign: This
control change message will affect the effect

10.5 Effect control

(JUMP #212)
(JUMP #218)
parameter selected in
and 032 are reserved for the Bank Select mes-
sage, and are not available.) For more details, on
controllers, refer to Common data 12.(F2)
Controller set (Modulation).
Aftertouch: Pressing down on the keyboard after
playing a note will affect the effect parameter
selected in
Velocity: The key-on velocity of the most
recently played note will affect the effect param-
eter selected in
Key Scale: The keyboard position of the most
recently played note will affect the effect param -
eter selected in If "Mi"
higher notes will result in a higher parameter
setting.
LFO: The Effect LFO will affect the effect
parameter selected in
Mi (0...99): When the controller is at minimum
position (e.g., the modulation wheel is moved
fully toward you, no aftertouch pressure is being
applied, etc.), the parameter will be set to this
percentage of its maximum value. (See also
"Ma"
Ma (0...99): When the controller is at maximum
position (e.g., the modulation wheel is moved
fully away from you, the maximum aftertouch
pressure is being applied, etc.), the parameter
will be set to this percentage of its maximum
value.
You can set the "Mi" value above the
"Ma" value to reverse the effect of the con-
troller. For example if "Mi" is 99 and "Ma" is
50, and you have set the "Ctrl# & Device" to be
"001 Modulation", the selected parameter will
be at 100% of its full range when the modulation
wheel is moved fully toward you, and at 50% of
its full range when the modulation wheel is
moved fully away from you.
LFO: A special Effect LFO is provided for con-
trolling the effect parameters you select in
You can set the waveform (WV= triangle, saw
down, saw up, square, sine, sample&hold), the
speed (Sp= 0...99), the delay (D1= 0...99), and
the initial phase Ph= 0...99, free) of the Effect
LFO. For a detailed explanation of these param-
eters, refer to AFM element data 6.(F1) AFM
VOICE EDIT MODE
JUMP #218
(Control numbers 000
is below "Ma"
below.
See
123