Points To Note When Turning Off The Main Power; Stirring Toner; Cassette Setting; Apvc Correction Of Drum - Canon iR3245 Series Service Manual

Chapter 2
Use the correct power code to mach the location/area of installation.
Make sure not to leave unused power code at the site.
4) Turn ON the main power switch.

2.2.8 Points to Note When Turning OFF the Main Power

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
Turning OFF the main power
When turning off the main power, follow the procedures described below
to protect the hard disk
1) Hold down the control panel power switch for 3 sec or more.
2) Operate the control panel as instructed on the shut-down sequence
screen. (The main power will go off automatically.)
3) Unplug the power plug.

2.2.9 Stirring Toner

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
1) Enter the service mode.
Select: COPIER > FUNCTION > INSTALL > TONER-S.
MEMO:
Stirring toner operation takes for approx 6 min. After counted, it
automatically stops. Perform the cassette setting before the completion of
toner stirring. (Refer to the cassette setting.)
2) When the count displays "OK!", exit the service mode.

2.2.10 Cassette Setting

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
1) Press the cassette release button to pull out the cassette.
2) Check the paper type that users will be using and make sure that the size
type selection switch [1] of the cassette matches with the required paper
size type. If not, adjust the position of the size type selection switch to the
corresponding paper size type.
3) Adjust the paper size registration dial [2] to the requires paper size.
[2]
4) Pick the lever [1] on the side guide plate and adjust the side guide plate to
the intended size.
5) Tilt the side guide plate and remove it. Adjust the leading edge guide plate
[2] to the intended size by following the instruction on the bottom on the
cassette.
2-14
[1]
F-2-56
0019-0209
6) Put the paper size label [1] corresponding to the paper set on front of the
cassette.
0019-0210
7) Set the paper into the cassette and put back the cassette.
8) Specify the setting for the other cassette in the same manner.
0019-4001
9) If the cassette feeding unit is installed, refer to the installation procedure
of cassette pedestal to specify the cassette settings.

2.2.11 APVC Correction of Drum

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
1) Enter the service mode.
Select: COPIER > FUNCTION > DPC > D-GAMMA.
MEMO:
After the paper is picked up from the cassette 1, blank paper is delivered
and APVC correction completes automatically (indifferent to paper size in
the cassette).
2) Exit the service mode.
Just after the stirring toner, floating toner inside the body due to toner
stirring may attaches to the test print (back side) slightly. This will be
cleared after making a couple of copies.

2.2.12 Auto Gradation Correction

iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
1) Open the platen cover/DADF.
2) Clean the copyboard glass.
3) Set the A3, A4, 11x17 or LTR paper into the cassette. (refer to the cassette
settings.)
4) Press [Additional Functions].
5) Press [Adjustment/Cleaning] > [Auto Gradation Adjustment] > [Test
Print].
[2]
[1]
F-2-57
F-2-58
[1]
0019-4002
0019-4381