Fujitsu PRIMERGY RX2540 M1 Upgrade And Maintenance Manual page 15

9.6.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 230
9.6.4.2 Removing the FBU . . . . . . . . . . . . . . . . . . . . . . 230
9.6.4.3 Removing the riser module 2 (FL) . . . . . . . . . . . . . . 231
9.6.4.4 Removing a GPGPU card (FL) . . . . . . . . . . . . . . . . 231
9.6.4.5 Installing the slot cover (riser module 2) . . . . . . . . . . . 231
9.6.4.6 Installing the rear cover (riser module 2) . . . . . . . . . . . 231
9.6.4.7 Insert the riser module 2 (FL) . . . . . . . . . . . . . . . . 232
9.6.4.8 Installing the system air duct . . . . . . . . . . . . . . . . . 232
9.6.4.9 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 232
9.6.5 Replacing GPGPU cards in riser modules . . . . . . . . . . . . 232
9.6.5.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 232
9.6.5.2 Removing the defective GPGPU card . . . . . . . . . . . . 233
9.6.5.3 Installing the new GPGPU card . . . . . . . . . . . . . . . 233
9.6.5.4 Connecting cables to the GPGPU card . . . . . . . . . . . 233
9.6.5.5 Connecting a battery backup unit to the expansion card . . . 233
9.6.5.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 234
9.6.6 Replacing a riser card . . . . . . . . . . . . . . . . . . . . . . 234
9.6.6.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 234
9.6.6.2 Removing the defective GPGPU card . . . . . . . . . . . . 235
9.6.6.3 Installing the new GPGPU card . . . . . . . . . . . . . . . 235
9.6.6.4 Connecting cables to the expansion card . . . . . . . . . . 236
9.6.6.5 Connecting a battery backup unit to the expansion card . . . 236
9.6.6.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 236
9.7 Backup Units . . . . . . . . . . . . . . . . . . . . . . . . . . 236
9.7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . . 236
9.7.2 Installing a FBU . . . . . . . . . . . . . . . . . . . . . . . . . 237
9.7.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 237
9.7.2.2 Installing TFM to the RAID controller (if applicable) . . . . . 238
9.7.2.3 Preparing the FBU . . . . . . . . . . . . . . . . . . . . . . 241
9.7.2.4 Connecting the FBU to the RAID controller . . . . . . . . . 241
9.7.2.5 Installing the FBU holder onto the air duct . . . . . . . . . . 243
9.7.2.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 244
9.7.3 Removing a FBU
9.7.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 244
9.7.3.2 Removing the FBU holder from the air duct . . . . . . . . . 245
9.7.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 246
9.7.4 Replacing a FBU . . . . . . . . . . . . . . . . . . . . . . . . . 247
9.7.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 247
9.7.4.2 Removing a FBU from the air duct . . . . . . . . . . . . . . 248
9.7.4.3 Disconnecting the FBU cable from the FBU . . . . . . . . . 248
9.7.4.4 Removing the FBU from the holder . . . . . . . . . . . . . 249
RX2540 M1
. . . . . . . . . . . . . . . . . . . . . . . . 244
Upgrade and Maintenance Manual
Contents
15