ZyXEL Communications UAG Series Cli Reference Manual page 102

Chapter 12 Virtual Servers
The following table lists the virtual server commands.
Table 50 ip virtual-server Commands
COMMAND
show ip virtual-server [profile_name] Displays information about the specified virtual server or about all the virtual
no ip virtual-server profile_name
ip virtual-server profile_name
interface interface_name original-ip
{any | ip | address_object} map-to
{address_object | ip} map-type
[nat-loopback [nat-1-1-map]
[deactivate] | nat-1-1-map
[deactivate] | deactivate]
ip virtual-server profile_name
interface interface_name original-ip
{any | IP | address_object} map-to
{address_object | ip} map-type
protocol {any | tcp | udp} original-
port <1..65535> mapped-port
<1..65535> [nat-loopback [nat-1-1-
map] [deactivate] | nat-1-1-map
[deactivate] | deactivate]
ip virtual-server profile_name
interface interface_name original-ip
{any | IP | address_object} map-to
{address_object | ip} map-type
protocol {any | tcp | udp} original-
port-begin <1..65535> original-port-
end <1..65535> mapped-port-begin
<1..65535> [nat-loopback [nat-1-1-
map] [deactivate] | nat-1-1-map
[deactivate] | deactivate]
102
DESCRIPTION
servers.
Deletes the specified virtual server.
Creates or modifies the specified virtual server and maps the specified
destination IP address (for all destination ports) to
address object or IP
specified interface (any), the specified IP address (IP), or the specified
any
address object (address-object). NAT loopback allows local users to use a
domain name to access this virtual server.
Select what kind of NAT this rule is to perform.
nat-1-1-map: means the NAT type is either 1:1 NAT or many 1:1 NAT. See
Section 12.1.1 on page 101
Using this command without nat-1-1-map means the NAT type is Virtual
Server. This makes computers on a private network behind the UAG available
to a public network outside the UAG (like the Internet).
The deactivate command disables the virtual server rule.
Creates or modifies the specified virtual server and maps the specified
(destination IP address, protocol, and destination port) to
(destination IP address and destination
defined by the specified interface (any), the specified IP address (IP), or the
port
specified address object (address-object). NAT loopback allows local users
to use a domain name to access this virtual server.
nat-1-1-map: means the NAT type is either 1:1 NAT or many 1:1 NAT. See
Section 12.1.1 on page 101
Using this command without nat-1-1-map means the NAT type is Virtual
Server. This makes computers on a private network behind the UAG available
to a public network outside the UAG (like the Internet).
The deactivate command disables the virtual server rule.
Creates or modifies the specified virtual server and maps the specified
(destination IP address, protocol, and range of destination ports) to
specified (destination IP address and range of destination
destination IP is defined by the specified interface (any), the specified IP
ports
address (IP), or the specified address object (address-object). NAT
loopback allows local users to use a domain name to access this virtual
server.
nat-1-1-map: means the NAT type is either 1:1 NAT or many 1:1 NAT. See
Section 12.1.1 on page 101
Using this command without nat-1-1-map means the NAT type is Virtual
Server. This makes computers on a private network behind the UAG available
to a public network outside the UAG (like the Internet).
The deactivate command disables the virtual server rule.
address. The original destination IP is defined by the
for more information.
port). The original destination IP is
for more information.
for more information.
the specified destination
the specified
the
ports). The original
UAG CLI Reference Guide