Epson EPL-N4000 Service Manual page 45

EPSON EPL-N4000/EPL-N4000+
Table 1-32. Printer Setting
Menu Item
*1
Network • Network config
Menu
*2,3
• Get IPAddress
*2,3
• IP Byte 1
*2,3
• IP Byte 2
*2,3
• IP Byte 3
*2,3
• IP Byte 4
*2,3
• SM Byte 1
*2,3
• SM Byte 2
*2,3
• SM Byte 3
*2,3
• SM Byte 4
*2,3
• GW Byte 1
*2,3
• GW Byte 2
*2,3
• GW Byte 3
*2,3
• GW Byte 4
*3
• Buffer Size
*4 *5
AUX Menu • AUX Config
*5,6
• Get IPAddress
*5,6
• IP Byte 1
*5,6
• IP Byte 2
*5,6
• IP Byte 3
*5,6
• IP Byte 4
*5,6
• SM Byte 1
*5,6
• SM Byte 2
*5,6
• SM Byte 3
*5,6
• SM Byte 4
*5,6
• GW Byte 1
*5,6
• GW Byte 2
*5,6
• GW Byte 3
*5,6
• GW Byte 4
*5,6
• Netware
*5,6
• AppleTalk
*5,6
• NetBEUI
*5,6A
• AUX Init
*3
• Buffer Size
Rev.B
Value
• No, Yes (added in EPL-N4000+)
• Panel, Auto, PING (added in EPL-
N4000+)
• 192 , 0 to 255 (added in EPL-N4000+)
• 168, 0 to 255 (added in EPL-N4000+)
• 192 , 0 to 255 (added in EPL-N4000+)
• 168, 0 to 255 (added in EPL-N4000+)
• 255, 0 to 255 (added in EPL-N4000+)
• 255, 0 to 255 (added in EPL-N4000+)
• 255, 0 to 255 (added in EPL-N4000+)
• 0 , 0 to 255 (added in EPL-N4000+)
• 255, 0 to 255 (added in EPL-N4000+)
• 255, 0 to 255 (added in EPL-N4000+)
• 255, 0 to 255 (added in EPL-N4000+)
• 255 , 0 to 255 (added in EPL-N4000+)
• Normal, Maximum, Minimum
• No, Yes (added in EPL-N4000+)
• Panel, Auto, PING (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• 0 to 255 (added in EPL-N4000+)
• On,Off (added in EPL-N4000+)
• ON, Off (added in EPL-N4000+)
• ON, Off (added in EPL-N4000+)
• Normal, Maximum, Minimum
NOTE: *1: Automatically returns to "Network Config =No" after
shifting to "Ready".
*2: Appears only when "Network Config=Yes", and can then
be selected. Always printed on Status Sheet.
*3: When changed on the panel or with EJL, these do not
become valid immediately but become valid after warm boot
or at power on again. Displaying on the panel, reading with
EJL, and printing on the status sheet for themselves are
immediately reflected. They are not reflected in the out bin
setting range, language, network operation etc. until warm
boot is performed or the power is turned on again. If they are
changed on the panel or with EJL, be sure to perform warm
boot or turn on the power again. To change more than one of
these, change more than one of them, perform, warm boot
or turn on the power again once at the end.
*4: Appears only when the TypeB interface card is installed.
*5: Appears only a Level 3-capable Type B host interface
(option) is installed, and can then be selected or executed.
Automatically returns to "AUX Config=No" after shifting to a
printable state.
*6: Appears only when "AUX Congig=Yes" is selected, and
can then be selected or executed. The setting value
becomes valid when the network card is restarted after
shifting to a printable state. Therefore, when the setting
value is changed, if "AUX Status Sheet" in the test print
menu is executed before coming out of the panel setting
mode, the before change setting value is printed. Before
setting or executing menus other than these items, shift to a
printable state.
CHAPTER 1 Product Description
31