Advertisement
bizhub C4000i/C3300i
3.6.4 C0204
Contents
Trouble type
C0204: Tray 2 feeder up/down abnormality (When PF-P20 or PF-P21 is installed)
Rank
B
Trouble detection condition The tray 2 upper limit sensor (PS2/2) is not turned ON (blocked) even after the set period of time has elapsed after
the paper lift-up operation for the drawer began.
Trouble isolation
Tray 2
Relevant electrical parts
Procedure
1.
Remove the tray
and check to see if a piece of paper is not left inside the machine.
2. Check the connector between M2/2-PCCB/2 CN4 for proper connection and correct as necessary.
3. Check the connector of M2/2 for proper drive coupling and correct as necessary.
4. Check the connector between PS2/2-PCCB/2 CN3 for proper connection and correct as necessary.
5. Check the connector between PCCB/2 CN1-relay CN24-BASEB CN21E for proper connection and correct as necessary.
6. Check CPUB for proper installation and correct as necessary.
7. PS2/2 I/O check, sensor check
• Control signal: PCCB/2 CN3-9 (ON)
• Location of electrical component: 18-X
8. M2/2 load check
• Check code: 23
• Multi code: 5
• Control signal: PCCB/2 CN4-8 to 9
• Location of electrical component: 18-P
9.
Replace M2/2.
10.
Replace PCCB/2.
11.
Replace CPUB.
12.
Replace BASEB.
3.6.5 C0206
Contents
Trouble type
C0206: Tray 3 feeder up/down abnormality (When PF-P20 or PF-P21 is installed) (bizhub C4000i only)
Rank
B
Trouble detection condition The tray 3 upper limit sensor (PS2/3) is not turned ON (blocked) even after the set period of time has elapsed after
the paper lift-up operation for the drawer began.
Trouble isolation
Tray 3
Relevant electrical parts
Procedure
1.
Remove the tray
and check to see if a piece of paper is not left inside the machine.
2. Check the connector between M2/3-PCCB/3 CN4 for proper connection and correct as necessary.
3. Check the connector of M2/3 for proper drive coupling and correct as necessary.
4. Check the connector between PS2/3-PCCB/3 CN3 for proper connection and correct as necessary.
5. Check the connector between PCCB/3 CN1-relay CN2PC-PCCB/2 CN2 for proper connection and correct as necessary.
6. Check the connector between PCCB/2 CN1-relay CN24-BASEB CN21E for proper connection and correct as necessary.
7. Check CPUB for proper installation and correct as necessary.
8. PS2/3 I/O check, sensor check
• Control signal: PCCB/3 CN3-9 (ON)
• Location of electrical component: 18-X
9. M2/3 load check
• Check code: 23
• Multi code: 6
• Control signal: PCCB/3 CN4-8 to 9
• Location of electrical component: 18-P
10.
Replace M2/3.
11. PCCB/3 F2 conduction check
12.
Replace PCCB/3.
13.
Replace CPUB.
14.
Replace BASEB.
• Tray 2 lift-up motor (M2/2)
• Tray 2 upper limit sensor (PS2/2)
• Tray 2 PC control board (PCCB/2)
• CPU board (CPUB)
• Base board (BASEB)
• Tray 3 lift-up motor (M2/3)
• Tray 3 upper limit sensor (PS2/3)
• Tray 3 PC control board (PCCB/3)
• CPU board (CPUB)
• Base board (BASEB)
L TROUBLESHOOTING > 3. TROUBLE CODE
L-24
Advertisement
