Siemens SINAMICS G120 Function Manual page 342

Index
SAM (Safe Acceleration Monitor), 130, 135, 180
active, 160
SBC (Safe Brake Control), 30
Acceptance test, 289
Requested, 160
SBR (Safe Brake Ramp), 130, 179, 189, 195, 196
active, 160
SDI (Safe Direction), 37
Acceptance test, 301
active, 160
Delay time, 147
deselect, 160
Discrepancy, 221
Fault response, 223
select, 216
Switch off the motor, 217
Switch on motor, 219
Tolerance, 147
Self-test, 98
Self-test (forced dormant error detection), 105
Serial number, 311
Series commissioning, 155, 158
Service life, 267
Service personnel, 15
Setpoint speed limit, 193
Shared Device, 44, 82, 92, 129
Signals, 160
SIL (Safety Integrity Level), 273
SIMATIC ET 200pro FC-2, 20, 21, 51
SINAMICS G110M, 20, 21
SINAMICS G120
CU230P-2, 20, 21
CU240B-2, 20, 21
CU240E-2, 20, 21
CU250S-2, 20, 21
SINAMICS G120C, 20, 21
SINAMICS G120D
CU240D-2, 20, 21
CU250D-2, 20, 21
SIZER, 336
SLS (Safely Limited Speed), 34, 189
Acceptance test, 292
active, 160
Braking ramp monitoring, 140
Delay time, 140
deselect, 160, 189
Discrepancy, 202
Fault response, 204
Level, 195
Level active, 160
Monitoring mode, 189
Monitoring threshold, 196
342
Response, 138
select, 189, 191, 193
Select level, 160
Setpoint speed limit, 138
Speed monitoring, 140
Standstill monitoring, 199
Switch off the motor, 199
Switch on motor, 201
Switching monitoring threshold, 195
Switching over speed monitoring, 196, 198
Speed monitoring, 227
Speed ratio, 107
Spindle drive, 36
SS1 (Safe Stop 1), 32
Acceptance test, 283, 286
active, 160
Delay time, 130, 131, 132, 134
Delay time for SBR, 130
deselect, 160
Discrepancy, 183, 185
Fault response, 187
Monitoring mode, 130
Monitoring time, 132, 132
Reference speed, 132, 132
Reference speed (reference velocity), 132
Reference velocity (reference speed), 132
select, 130, 178, 179
Shutdown speed, 130, 131, 133, 134
Speed tolerance, 134
Standstill monitoring, 130, 131, 179, 180
Switch off the motor, 182
Tolerance, 130, 135
Zero speed detection, 133
SSM (Safe Speed Monitoring), 39
Acceptance test, 297
Fault response, 230
Feedback signal active, 160
Filter, 144
Hysteresis, 144
Speed limit, 143
Switch off the motor, 208
Switch on motor, 213
Time response, 207
Standard acknowledgment, 160
STARTER, 84
STARTER commissioning tool, 84
STARTER PC tool, 84
Status F-DI via PROFIsafe, 128
Status word 1, 47, 49
Status word 5, 50
STO (Safe Torque Off), 27
Acceptance test, 279, 281
Safety Integrated - SINAMICS G110M, G120, G120C, G120D and SIMATIC ET 200pro FC-2
Function Manual, 04/2014, FW V4.7, A5E34261271B AA