Download  Print this page

Advertisement

Enabling automatic acquisition of the IP
address
When the unit is shipped from the factory, automatic
acquisition of the IP address is disabled. Proceed as
follows to enable it.
1
Holding down the MENU knob, set the menu switch
from OFF to ON.
The TOP menu appears.
2
Turn the MENU knob to move the b mark to
"MAINTENANCE", and press the MENU knob.
If this is the first time the MAINTENANCE menu has
been displayed, the CONTENTS page appears.
If the menu has been used before, the last accessed
page appears.
3
If the CONTENTS page is displayed, turn the MENU
knob to move the b mark to "NETWORK", and press
the MENU knob.
If a different page is displayed, turn the MENU knob
until the NETWORK page appears, then press the
MENU knob.
The NETWORK page appears. The current settings of
the items on the page appear to the right of the items.
M18 NETWORK
DHCP
IP ADDRESS
SUBNET MASK
DEF. GATEWAT
LINK SPEED
DUPLEX
4
Press the MENU knob, and turn it to move the b mark
to "DHCP", then press the MENU knob.
The b mark to the left of "DHCP" changes to a z
mark, and the z mark to the left of the setting changes
to a ? mark.
5
Turn the MENU knob to display "ENABL", then press
the MENU knob.
The z mark changes to a b mark and the ? mark
changes to a z mark.
6
To end the menu operation, set the MENU ON/OFF
switch to OFF.
Note
Before enabling automatic acquisition of the IP address,
check to be sure that this unit is connected to a network
with a network cable.
TOP
:
DISABL
:
192 168 1 10
:
255 255 255 0
:
0 0 0 0
:
AUTO
:
AUTO
The acquired IP address is displayed in the "IP
ADDRESS" line of the NETWORK page.
If an IP address could not be acquired, "0.0.0.0" is
displayed. In this case, contact your network
administrator.
Setting the IP address, subnet mask, and
default gateway
The unit is shipped from the factory with the following
settings.
IP ADDRESS:
192.168. 1.10
SUBNET MASK: 255.255.255. 0
DEF. GATEWAY:
0. 0. 0. 0
Proceed as follows to change the settings.
1
Carry out steps 1 to 3 in "Enabling automatic
acquisition of the IP address" (page 145) to display
the NETWORK page of the MAINTENANCE menu.
2
Turn the MENU knob to move the b mark to "IP
ADDRESS", then press the MENU knob.
The IP ADDRESS setting window appears.
3
Move the b mark to the value that you want to change,
then press the MENU knob.
The b mark changes to a ? mark.
4
Turn the MENU knob to display the desired value,
then press the MENU knob.
The ? mark changes to a b mark.
To cancel the change and restore the standard
setting
Push the CANCEL/PRST/ESCAPE switch to the
CANCEL/PRST side.
For details, see 7-1-3 "Basic Menu Operations" (page
118).
5
Repeat steps 3 and 4 to set the remaining values.
6
When you are finished, move the b mark to SET, then
press the MENU knob.
7
Turn the MENU knob to move the b mark to
"SUBNET MASK", then press the MENU knob.
SUBNET MASK setting window appears.
8
Carry out steps 3 to 6 to set the subnet mask.
9
Turn the MENU knob to move the b mark to "DEF.
GATEWAY", then press the MENU knob.
The DEF. GATEWAY setting window appears.
7-3 Adjustments and Settings From Menus
145

Advertisement

Table of Contents

   Related Manuals for Sony PDW-510

This manual is also suitable for:

Pdw-510pPdw-530pPdw-530

Comments to this Manuals

Symbols: 0
Latest comments: