Download  Print this page

Recording In Live Logging Mode - Sony PDW-510 Operation Manual

Hide thumbs

Advertisement

To set the initial value to any number
Proceed as follows.
1
On the CLIP TITLE page of the OPERATION menu
(see page 63), select "CLEAR NUMERIC" and then
press the MENU knob.
An initial value appears.
23 CLIP TITLE
0123456789
INS DEL RET
CLEAR NUMERIC
LOAD PREFIX DATA:
PREFIX
NUMERIC : 00001
2
Move the x mark to the digit you want to change and
then press the MENU knob.
3
Rotate the MENU knob to move the x mark to the
desired digit in the list of selectable digits, and then
press the MENU knob.
4
Repeat steps 2 and 3 to enter the remaining digits.
5
When you have finished entering the value, rotate the
MENU knob to move the x mark to "END", and then
press the MENU knob.
The camcorder exits numeric input mode, and the
original CLIP TITLE page appears.
Notes
• It is not possible to specify 00000 as the initial value.
Even if you enter 00000, the value is reset to 00001
when the camcorder exits numeric input mode.
• The value of the serial number is incremented by 1
every time a title is generated. When the value
reaches 99999, the next number restarts from 00001.
• Duplicate clip titles can be generated if you reset the
serial number after recording several clips or the
same is true depending on the value setting. Care
should be taken when setting the serial number.
3-2-9 Recording in Live Logging
1)
Mode
1) This is supported from firmware version 1.4 and PDZ-1 version 1.4.
Live logging is a function that allows you to
simultaneously transfer logging data as you record live
material.
You can install the optional CBK-NC01 Network Adaptor
in the camcorder, and connect to the adaptor's network
connector from the PDZ-1 Proxy Browsing Software to do
the following.
64
3-2 Recording
ESC END
:
EXEC
EXEC
: TITLE
• View proxy AV data.
• Add and modify metadata (titles, comments, essence
marks, etc.).
• Create clip lists.
After adding or modifying metadata and clip lists, you can
transfer them from the computer back to the camcorder for
recording on the original disc.
Refer to the PDZ-1 help for more information about PDZ-
1 functions and operations.
To record in live logging mode
With the optional CBK-NC01 network adaptor installed
on the camcorder, proceed as follows.
1
Use an Ethernet cable to connect the camcorder to a
computer with PDZ-1 installed.
2
In the TOP menu, select "OPERATION".
3
Turn the MENU knob to scroll to the OUTPUT page.
Alternatively, in the CONTENTS page, select
"OUTPUT".
The OUTPUT page appears.
4
Turn the MENU knob to select "LIVE LOGGING",
and then press the MENU knob.
U01 OUTPUT
LCD BRIGHT <L>
LCD BRIGHT <H>
LCD COLOR
i.LINK MODE
PB WIDE ID(IMX) :
REAR BNC OUT SEL:
LIVE LOGGING
5
Turn the MENU knob to display "ON", and then press
the MENU knob.
The camcorder enters Live Logging mode.
6
Start recording in the normal way, by pressing the
REC START button or the VTR button on the lens.
Notes
• In Live Logging mode, you cannot set the F-RUN/SET/
R-RUN switch to SET to make time code settings. To
make time code settings, first exit Live Logging mode.
• During Live Logging operations, the time code
generator run mode is always F-RUN, regardless of the
setting of the F-RUN/SET/R-RUN switch.
• In Live Logging mode, you cannot set the PRESET/
REGEN/CLOCK switch to REGEN to read time code
from the disc and generate consecutive time code.
TOP
:
0
:
0
:
0
:
AV/C
THROU
VBS
:
OFF

Advertisement

Table of Contents

   Related Manuals for Sony PDW-510

This manual is also suitable for:

Pdw-510pPdw-530pPdw-530

Comments to this Manuals

Symbols: 0
Latest comments: