Specifying The Brightness Of The Touch Screen, Leds, Channel Name Displays, And Lamps - Yamaha CL5 Reference Manual

3
Send point select buttons (MATRIX bus only)
Select the pre-fader send point. These buttons correspond to the following parameters.
Button Pre-fader send point
PRE EQ Immediately before the EQ
PRE FADER Immediately before the fader
4
PAN LINK button
This button appears only if two adjacent buses are paired in stereo. If the button is on, the pan
setting of signals sent from input channels to the corresponding two buses will link with the
STEREO bus pan setting.
3.
Use the MIX BUS SETUP/MATRIX BUS SETUP tabs to view either the MIX buses or
the MATRIX buses.
4.
Use the buttons in the SIGNAL TYPE field to specify whether each bus will function
as STEREO (main parameters will be linked for two adjacent odd-numbered/even-
numbered buses) or MONOx2 (use as two monaural channels).
5.
Use the buttons of the PRE FADER SEND POINT/BUS TYPE field to select the
position from which the signal of the input channel will be sent.
In the case of a MIX bus, you can use this field to switch the type of bus (VARI or FIXED).
6.
As desired, turn the buttons in the PAN LINK field on or off.
In the PAN LINK field, you can specify whether the panning of the signal routed from an input
channel to the stereo bus will be linked with operation of the INPUT TO ST PAN knob (if the
input channel's SIGNAL TYPE is set to STEREO and BUS TYPE is set to VARI).
• If the PAN LINK button is on:
If the send-destination bus is stereo, the PAN knob that appears in the location of the SEND
LEVEL knob on the screens for input channels will be linked with the INPUT TO ST PAN knob.
• If the PAN LINK button is off:
The PAN knob that appears in the location of the SEND LEVEL knob on the screens for input
channels can be operated independently of the INPUT TO ST PAN knob.
Specifying the brightness of the touch screen,
LEDs, channel name displays, and lamps
Follow the steps below to specify the brightness of the touch screen, top panel LEDs, channel name
displays, and lamps connected to the rear panel LAMP connectors.
1.
In the Function Access Area, press the SETUP button to access the SETUP screen.
2.
In the field located in the right of the bottom row of the SETUP screen, press the
BANK A or BANK B button.
You can save two different brightness settings in bank A and B, and switch between them rapidly
if desired.
3.
Use the multifunction knobs to set the following parameters.
CONTRAST field
• NAME......................... Adjusts the contrast of the characters in the channel name displays on
the top panel.
BRIGHTNESS field
• NAME......................... Adjusts the brightness of the channel name displays on the top panel.
• CH COLOR ............... Adjusts the brightness of the channel colors on the top panel.
• SCREEN..................... Adjusts the brightness of the touch screen. If the brightness is set to lower
than level 2, the CL will start up next time with a brightness setting of 2
so that you will be able to see the screen.
• PANEL........................ Adjusts the brightness of the top panel LEDs. If the optional MBCL
meter bridge is installed on the CL3/CL1, this knob setting will also
affect the LEDs on the meter bridge.
NOTE
If the AD8HR is connected, the brightness of the AD8HR's LEDs will also change.
• LAMP.......................... Adjusts the brightness of the lamps connected to the rear panel LAMP
jacks.
4.
If desired, switch between banks A and B and make settings for the other bank in
the same way.
Now you can switch between the BANK A and BANK B buttons to change the brightness of the
touch screen, LCD, channel name displays, and lamps in a single operation. You can also assign
this parameter to a USER DEFINED key, and press that key to switch between banks A and B.
193
Other functions
Reference Manual