Yamaha CL5 Reference Manual page 245

FUNCTION PARAMETER 1 PARAMETER 2
BOOKMARK
PAGE
CHANGE
BOOKMARK with "SEL" —
PREVIOUS PAGE
—
NEXT PAGE
CLOSE POPUP —
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
TRANSPORT
AUTO REC
RECORDER
REC & START
NO ASSIGN
(TITLE 1)
DIRECT PLAY
:
INC RECALL —
REC RECALL —
SCENE
DIRECT RECALL SCENE #000–#300
RECALL UNDO —
STORE UNDO —
SEND
MIX1-16/MIX17-24,
ENCODER —
MATRIX
MODE
MIX1–MIX24
MTRX1–MTRX8
SENDS ON
MIX ON FADER —
FADER
MATRIX ON FADER
SENDS ON FADER
Explanation
Memorize the currently selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (press and
release the key within two seconds). Popup
screens can also be memorized. In the case of a
rack, the number of that rack is also
memorized.
Memorize the above BOOKMARK with the
addition of the SEL status.
Display the previous/next page.
Close the displayed popup window.
Display the previous/next page.
Shortcut function for STOP → REC → PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then
recording will continue with a new file.
Start recording immediately without entering
record-ready mode.
The specified audio file will be played once
from the beginning. Audio files to be played
should be saved in the SONGS folder inside the
YPE folder. Please note that a file cannot be
specified if it is saved in the root directory or in
any other folder. When you execute playback,
the path in the TITLE LIST screen will move to
\YPE\SONGS\.
Recall the scene of the next existing number.
Recall the scene of the previous existing
number.
Directly recall the scene of the specified
number.
Execute RECALL UNDO.
Execute STORE UNDO.
If INPUT or ST IN is selected, switch the
function of the Selected Channel section's send
encoders from TO MIX1-16/TO MIX17-24,
MATRIX.
Switches the MIX ON FADER function for the
selected MIX on and off.
Switches the MATRIX ON FADER function for
the selected MATRIX on and off.
Switches the MIX ON FADER function on and
off.
Switches the MATRIX ON FADER function on
and off.
Switches the SENDS ON FADER function on
and off.
245
FUNCTION PARAMETER 1 PARAMETER 2
SET [+48V]
SET [Ø]
SET [INSERT ON]
SET [DIRECT OUT ON]
SET [PRE SEND]
SET BY SEL —
SET [TO STEREO]
SET [TO MONO]
SET [TO LCR]
SET [GAIN
COMPENSATION]
SET DEFAULT
— —
VALUE
SET
NOMINAL — —
VALUE
LATCH
TALKBACK ON
UNLATCH
TALKBACK
SELECTED CH ASSIGN —
DIRECT ASSIGN *3)
CURRENT PAGE —
TAP TEMPO
EFFECT RACK1–8 —
*1) CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48, ST IN 1L–ST IN 8R, MIX1–MIX24, MTRX1–MTRX8,
ST L, ST R, MONO(C)
*2) CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48, ST IN 1–ST IN 8, MIX1–MIX24, MTRX1–MTRX8,
STEREO, MONO(C)
*3) MIX1–MIX24, MTRX1–MTRX8, ST L, ST R, MONO(C)
*4) CL5: CH1–CH72, CL3: CH1–CH64, CL1: CH1–CH48, ST IN 1–ST IN 8, MIX1–MIX24, MTRX1–MTRX8,
STEREO, MONO(C), DCA1–DCA16
Appendices
Explanation
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on
or dark if off.
If SET [PRE SEND] is selected, "SEND ON
FADER" mode is engaged while you are
holding down the [SEL] key.
While holding down this key, press a knob in
the Selected Channel or Centralogic section to
reset it to the default value.
While holding down this key, press a [SEL] key
to set the fader of that channel to nominal
level.
Switch TALKBACK on/off.
Turn TALKBACK on while pressed.
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be
lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
Assign TALKBACK to the channel selected from
list 3).
Use the tap tempo function in the displayed
screen.
Use the tap tempo function for the specified
effect.
Reference Manual