Yamaha CL5 Reference Manual page 224

■ REV+SYMPHO.
One input, two output reverb and symphonic effects in parallel.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
REV/SYM 0–100% Reverb and symphonic balance (0% = all reverb, 100% = all symphonic)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE Used in conjunction with TEMPO to determine FREQ.
*1.
■ REVSYMPHO.
One input, two output reverb and symphonic effects in series.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
Reverb and symphonic reverb balance
REV.BAL 0–100%
(0% = all symphonic reverb, 100% = all reverb)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE Used in conjunction with TEMPO to determine FREQ.
*1.
Description
Description
224
■ REVPAN
This is a 1-in/2-out series-connected reverb and auto-pan effect.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
Reverb and panned reverb balance
REV.BAL 0–100%
(0% = all panned reverb, 100% = all reverb)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
*1
DIR. Panning direction
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*2
NOTE Used in conjunction with TEMPO to determine FREQ.
*1. LR, LR, LR, Turn L, Turn R
*2.
■ DELAY+ER.
One input, two output delay and early reflections effects in parallel.
Parameter Range
DELAY L 0.0–1000.0 ms Left channel delay time
DELAY R 0.0–1000.0 ms Right channel delay time
FB. DLY 0.0–1000.0 ms Feedback delay time
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN –99 to +99%
reverse-phase feedback)
HI. RATIO 0.1–1.0 High-frequency feedback ratio
Delay and early reflections balance
DLY/ER 0–100%
(0% = all delay, 100% = all early reflections)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
S-Hall, L-Hall, Random,
TYPE Type of early reflection simulation
Revers, Plate, Spring
ROOMSIZE 0.1–20.0 Reflection spacing
LIVENESS 0–10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
ER NUM. 1–19 Number of early reflections
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE L Used in conjunction with TEMPO to determine left channel DELAY L
NOTE R Used in conjunction with TEMPO to determine right channel DELAY R
*1
NOTE FB Used in conjunction with TEMPO to determine FB. DLY
*1
*1.
Appendices
Description
Description
(Maximum value depends on the tempo setting)
Reference Manual