Table of Contents
Advertisement
Grey Headline (continued)
Initial configuration
Powering on the VCS
To start the VCS:
1.
Ensure the power cable is connected.
2.
Ensure the LAN cable is connected to the
LAN 1 port.
3.
Turn on the power switch on the back right
of the unit (adjacent to the power cable).
4.
Press the soft power button on the back left
of the unit.
The system will power up. Wait until:
•
the green PWR LED on the front of the unit
is a steady green color (it may flash briefly
during power up).
•
the red ALM LED on the front of the unit has
gone out.
•
an IP address is showing in the display
panel on the front of the unit.
You now must set the system's IP address,
subnet mask and default gateway before the
system can be used. Consult your network
administrator for information on which
addresses to use. Note that the VCS must use
a static IP address.
The initial configuration can be done:
•
by connecting from a PC to the VCS
using a
serial cable
•
using the buttons on the front pane
l
•
if your network is set up to allow it, by
connecting using a web browser
to the
default IP address of 192.168.0.100.
If the red ALM LED flashes rapidly it
!
indicates a hardware fault. Contact your
local TANDBERG representative.
The yellow HDD LED indicates disk activity and
may flicker during normal operation, more so
on a busy system.
Overview and
Introduction
Getting started
status
D14049.05
February 2009
To set the initial configuration using a PC
connected to the VCS DATA port via a serial
cable:
1.
Connect the supplied serial cable from the
DATA port on the VCS to the COM port on a
PC.
2.
Start a terminal emulator program on the
PC and configure it to use the DATA port as
follows:
•
baud rate 115200
•
data bits: 8
•
parity: none
•
stop bits: 1
•
flow control: none.
Do not leave a terminal emulator
!
session open once it is no longer in
use. An open session may cause
issues during a system restart.
3.
Power on the unit (if it is not already on).
The terminal emulator program will display
start up information.
After approximately 2 minutes you will get
the login prompt (if the unit is already on,
press
Enter
to get the login prompt):
tandberg login:
4.
Enter the username
admin
and press Enter.
You will get the password prompt:
Password:
5.
Enter the default password of
TANDBERG
and press Enter.
You will get the install wizard prompt:
Run install wizard [n]:
y
Type
and press Enter.
System
VCS
Zones and
configuration
configuration
neighbors
Initial configuration using a serial cable
6.
Follow the prompts given by the install wizard
to specify the following:
a.
The password you want to use for your
admin
account. See
Default administrator
account
for details.
b.
Whether you wish to use IPv4, IPv6 or
Both. See
IP protocols
for details.
c.
The LAN 1 IP address of the system.
d.
The LAN 1 IPv4 subnet mask of the
system (if you have selected IPv4).
e.
The IP default gateway of the system.
f.
The
Ethernet
speed.
g.
Whether you want to use SSH to
administer the system.
h.
Whether you want to use Telnet to
administer the system.
7.
Once the wizard is finished you will be
prompted to log in again. Login with the
username
admin
and your new password.
8.
You will again get the install wizard prompt;
n
this time select
and press
Enter
to skip the wizard.
A welcome message similar to the following
will appear:
Welcome to
TANDBERG VCS Release X4.1
SW Release Date: 2009-02-01
OK
Call
Bandwidth
processing
control
22
TANDBERG
VIDEO COMMUNICATIONS SERVER
9.
You must now reboot the system in order
for the new settings take effect. To do this,
type the command:
xCommand boo
t
•
Once it has rebooted, the VCS is ready to use.
You can continue to use the serial connection,
or you can connect to the system remotely over
IP using either or both:
•
the
web interface
via HTTPS
•
a
command line interface
We recommend that you now configure the
following:
•
The system name of the VCS. This is used by
the TANDBERG Management Suite (TMS) to
identify the system. See
name
for more information.
•
Automatic discovery. If you have multiple
VCSs in the same network you may want
to disable automatic discovery on some
of them. See
Auto discover
information.
in order
•
The DNS server address (if URI dialing or
FQDNs are to be used). See the
servers
section for more information.
The IP configuration made using the
install wizard applies to the LAN 1
ethernet port only. If you have enabled
the LAN 2 port (by installing the Dual Network
Interfaces option key) you must use the web
interface or CLI to configure the LAN 2 settings.
Firewall
Applications
Maintenance
traversal
ADMINISTRATOR GUIDE
via SSH or Telnet.
About the system
for more
About DNS
Appendices
Advertisement
Table of Contents
