Danfoss FC 100 Series Operating Instructions Manual page 67

How to Programme the Frequ...
0-20 Display Line 1.1 Small
Option: Function:
[1667] Pulse Input #29 Actual value of the frequency applied at
[Hz] terminal 29 as a pulse input.
[1668] Pulse Input #33 Actual value of the frequency applied at
[Hz] terminal 33 as a pulse input.
[1669] Pulse Output Actual value of pulses applied to
#27 [Hz] terminal 27 in digital output mode.
[1670] Pulse Output Actual value of pulses applied to
#29 [Hz] terminal 29 in digital output mode.
[1671] Relay Output View the setting of all relays.
[bin]
[1672] Counter A View the present value of Counter A.
[1673] Counter B View the present value of Counter B.
[1675] Analog In Actual value of the signal on input
X30/11 X30/11 (General Purpose I/O Card.
Option)
[1676] Analog In Actual value of the signal on input
X30/12 X30/12 (General Purpose I/O Card.
Optional)
[1677] Analog Out Actual value at output X30/8 (General
X30/8 [mA] Purpose I/O Card. Optional) Use
par. 6-60 Terminal X30/8 Output to select
the variable to be shown.
[1680] Fieldbus CTW 1 Control word (CTW) received from the
Bus Master.
[1682] Fieldbus REF 1 Main reference value sent with control
word via the serial communications
network e.g. from the BMS, PLC or other
master controller.
[1684] Comm. Option Extended fieldbus communication
STW option status word.
[1685] FC Port CTW 1 Control word (CTW) received from the
Bus Master.
[1686] FC Port REF 1 Status word (STW) sent to the Bus
Master.
[1690] Alarm Word One or more alarms in a Hex code (used
for serial communications)
[1691] Alarm Word 2 One or more alarms in a Hex code (used
for serial communications)
[1692] Warning Word One or more warnings in a Hex code
(used for serial communications)
[1693] Warning Word One or more warnings in a Hex code
2 (used for serial communications)
[1694] Ext. Status One or more status conditions in a Hex
Word code (used for serial communications)
[1695] Ext. Status One or more status conditions in a Hex
Word 2 code (used for serial communications)
®
VLT HVAC Drive Operating Instructions
0-20 Display Line 1.1 Small
Option:
[1696]
[1830]
[1831]
[1832]
[1833]
[1834]
[1835]
[1836]
[1837]
[1838]
[1839]
[1850]
[2117]
[2118]
[2119]
[2137]
[2138]
[2139]
[2157]
[2158]
[2159]
®
MG.11.AD.02 - VLT is a registered Danfoss trademark
Function:
Maintenance The bits reflect the status for the
Word programmed Preventive Maintenance
Events in parameter group 23-1*
Analog Input Shows the value of the signal applied to
X42/1 terminal X42/1 on the Analog I/O card.
Analog Input Shows the value of the signal applied to
X42/3 terminal X42/3 on the Analog I/O card.
Analog Input Shows the value of the signal applied to
X42/5 terminal X42/5 on the Analog I/O card.
Analog Out Shows the value of the signal applied to
X42/7 [V] terminal X42/7 on the Analog I/O card.
Analog Out Shows the value of the signal applied to
X42/9 [V] terminal X42/9 on the Analog I/O card.
Analog Out Shows the value of the signal applied to
X42/11 [V] terminal X42/11 on the Analog I/O card.
Analog Input
X48/2 [mA]
Temp. Input
X48/4
Temp. Input
X48/7
Temp. Input
X48/10
Sensorless
Readout [unit]
Ext. 1 The value of the reference for extended
Reference Closed Loop Controller 1
[Unit]
Ext. 1 The value of the feedback signal for
Feedback extended Closed Loop Controller 1
[Unit]
Ext. 1 Output The value of the output from extended
[%] Closed Loop Controller 1
Ext. 2 The value of the reference for extended
Reference Closed Loop Controller 2
[Unit]
Ext. 2 The value of the feedback signal for
Feedback extended Closed Loop Controller 2
[Unit]
Ext. 2 Output The value of the output from extended
[%] Closed Loop Controller 2
Ext. 3 The value of the reference for extended
Reference Closed Loop Controller 3
[Unit]
Ext. 3 The value of the feedback signal for
Feedback extended Closed Loop Controller 3
[Unit]
Ext. 3 Output The value of the output from extended
[%] Closed Loop Controller 3
7 7
67