F4) Controllers Set (Other) - Yamaha SY77 Operating Manual

VOICE EDIT MODE
Pan LFO Depth (0...127): This determines the
range over which the specified controller will
regulate the depth of the Pan LFO. When this is
set to 127, the selected controller will regulate
LFO panning over the full range from no LFO
panning to maximum LFO panning. When this is
set to 0, the selected controller will have no
effect on LFO panning.
Pan Bias Depth (0...127): This determines the
range over which the specified controller will
affect pan position.
MIDI Ctrl No. & Device (0...120, After Touch):
These settings determine which controllers will
regulate the depth of LFO panning and Pan Bias.
To make controller settings for Pitch Bend,
Modulation, or Other, press F1, F2, or F4. Refer
to sections 12. (F1), 12. (F2), or 12. (F4).
MIDI Ctrl No. & Device: For details refer to 12.
(F2) Controller set (Modulation).
COMMON DATA
Summary: Specify controller devices that will regu-
late the volume, the EG bias and the Cutoff
Frequency of the filters in each element of the
voice.
Procedure:
From: Voice Common job
directory
Select: job 12:Ctrllr
Press: F4 (Othr)
Specify: the controller and depth for each
parameter
VolLowLimit (Volume Low Limit 0...127): This
determines the lowest volume that can be set by
the specified controller. For example when this
is set to 80, the controller will reduce the volume
no lower than 80. When this is set to 0, the con-
troller can reduce the volume to silence. When
this is set to 127, the controller will have no
1 1 2
12. (F4) Controller set (Other)
(JUMP #201)
(JUMP #228)
Remarks: Since the MODULATION 2 wheel is
detented at the center position, it is especially
useful for controlling pan. Since the MODULATION
2 wheel is assignable, to use it you must select
the MIDI Ctrl No. to which it has been assigned.
Check the Utility mode System Utility
3. Controllers (JUMP #803) settings to see the
MIDI Control Number to which the assignable
wheel has been set. For example if the
assignable wheel has been set to its initial set-
ting of MIDI Control Number 13, you would se-
lect "013:Non-assigned no." for the Pan Bias
control number in order to use WHEEL 2 to con-
trol panning.
Note: When a voice is used in Multi Play mode,
these Pan Control settings will be effective only
if the Static Pan is set to Voice. Refer to Multi
Edit 5. Voice static pan (JUMP #408, #409).
effect on the volume. In addition to the controller
specified here, the volume can always be con-
trolled over its full range by an optional foot con-
troller connected to the rear panel VOLUME jack.
EGbiasDepth (Eg Bias Depth 0...127): This
determines the range over which the specified
controller will control the EG bias. The result of
controlling EG Bias for an AFM element will
depend on the AModSens setting for each oper-
ator. If AModSens is set for carrier operators,
the controller assigned to EG Bias will affect the
volume of an AFM element. If AModSens is set
for modulator operators, the controller assigned
to EG Bias will affect the tone of an AFM ele-
ment. For details refer to Voice AFM Element
job 5. Sensitivity. For an AWM element, this
setting will affect the Volume.
CutoffDepth (Filter Cutoff Depth 0...127): This
determines the range over which the specified
controller will increase the cutoff frequency
specified for the filters of each element. Higher
settings will allow the controller to brighten the
tone. If the filter cutoff frequencies are already at
maximum, this will have no effect. See the
remarks below for details.
JUMP #228