Extron electronics DMP 64 User Manual page 112

Command and Response Table for DSP SIS Commands (continued)
Command
Audio group master commands
NOTE: • See
• A group must have assigned members for these commands to have an effect.
• For
• If entering a
•
Set a group fader control
Example:
Raise a group fader control
Example
Lower a group fader control
View the group fader control
level
Mute a group mute control
Clear (unmute) a group
mute control
View a group mute control
Set soft limits
Example:
View soft limits
View group type
View group members
NOTES:
X6) = Audio level control, or mix-point
select
X6% = Group master group number
X6^ = Group fader level
X6& = Group fader increase/decrease
X6* = Group fader soft limit
X6( = Group type
ASCII command
(host to device)
Group Masters on page 69, for more information about audio group masters.
X6^
, a positive (+) value is assumed unless a negative (–) value is specified.
X6^
value outside the valid range for the group or outside the soft limits, the DMP 64
responds with an "invalid parameter" (E13) error.
X6^ X6& X6*
, , and values can be sent without leading zeroes; responses are always 5 digits.
E X6% X6^
D * GRPM
E
d2*-293*GRPM
E X6% X6&
D * +GRPM
E }
d2*30+GRPM
E X6% X6&
D * -GRPM
E X6% }
D GRPM
E X6% }
*1GRPM
D
E X6% }
*0GRPM
D
E X6% }
GRPM
D
E X6% * X6* * X6*
L
upper
E
L2 * +60 * -60GRPM
E X6% }
GRPM
L
E X6% }
GRPM
P
E X6% }
O GRPM
See Table 1 on page 111 and 112.
0
dB value, in 0.1 dB increments, using negative numbers but not decimal
places. –1
range depends on the type of gain or trim block assigned to the group number
( X6% ).
dB value, in
dB value, in
the gain block grouped in X6% .
12 = mute
Response
(device to host)
} X6% X6^]
Grpm *
} ]
GrpmD02*-00293
} X6% X6^]
Grpm *
]
GrpmD02*-00263
} X6% X6^]
Grpm *
X6% X6^]
Grpm
*
X6%
*+00001
GrpmD
X6%
GrpmD *+00000
X6% X6$]
GrpmD
*
}
GRPM
lower
X6% X6* X6*]
GrpmL
* *
}
GrpmL02*+00060*-00060
X6% X6* X6*]
GrpmL
* *
X6% X6(]
GrpmP
*
X6% X6) X6)
GrpmO
* *
1
X6) ]
...*
16
1 - 32
00 0 0 0
. dB to +8 . dB is represented by –1
0
.1 dB increments, to raise or lower a group fader.
0
.1 dB increments. The valid range must be within the range for
6 = gain
DMP 64 • SIS Programming and Control
Additional description
Set the group fader to a value
X6^
of .
Set the group 2 fader control
to -29.3 dB.
Increase the level of the
X6&
group fader by dB.
Raise the group 2 fader 3 dB
(from -29.3 dB to -26.3 dB,
starting from the level set
in the "Set a group fader
control" example, above.
Decrease the level of the
X6&
group fader by dB.
In verbose modes 1 and 2, the
response is simplified to
X6^]
.
]
Mute all blocks in group
]
Umute all blocks in group
X6%
.
For group masters,
is always expressed as a
positive or negative 5-digit
value.
Set the groups soft limits to
X6* X6*
and .
]
Set the upper soft limit for the
group 2 fader to +6.0 dB and
the lower limit to -6.0 dB.
In verbose modes 0 and 1,
the response is simplified to
X6* X6*]
* .
Show the group type (
X6%
for group . In verbose
modes 0 and 1, the response
X6(]
is simplified to
X6)
* is the control or mix point.
2
In verbose modes 0 and 1,
the response is simplified to
X6) X6) X6)
* *...*
1 2 16
000 00
to 8 . The valid
X6%
X6%
X6%
.
X6$
X6(
)
.
]
.
106