Table of Contents
Advertisement
4．MENU Functions
4-1．List of MENU
All functions can be executed in the MENU screen.
MENU
(SCREEN CAPTURE)
MENU1
(FORMAT)
10.→480i SETUP LVL
11.SYNC
(The dashed-line-boxed items are effective with the CM-175 mounted.)
MENU2
(MODE)
10.SDI ERROR LED
11.FORMAT DISPLAY
MENU3
(VITC/WFM/VSC)
10.→DIMMER
11.→MAGNIFICATION
12.→SCALE
13.→POSITION
14.→COLOR
MENU4
MENU5
(VIDEO)
MENU6
(AUDIO)
(next page)
Setting the VBS input
1.VBS FORMAT
Setting the decoder Y/C separation
2.→Y/C SEP.
Setting the NTSC setup level
3.→NTSC SETUP LVL
Setting the VIDEO line signal of DVI inputs
4.DVI FORMAT
Setting the YPbPr/RGB signal format of DVI inputs
5.→YPbPr/RGB
Various setting of CM-175 COMPONENT inputs
6.COMP. FORMAT
7.→INPUT SELECT
Setting the analog PC/COMPONENT input selection
Setting the YPbPr/RGB signal format of COMP. inputs
8.→YPbPr/RGB
Setting the format with YPbPr/RGB 1125 line inputs
9.→1035/1080i
Setting the 480i foemat setup level
Setting SYNC INT/EXT
1.FUNCTION1 MODE
Setting the function assignment of F1(Function 1)switch
Setting the function assignment of F2(Function 2)switch
2.FUNCTION2 MODE
Setting the monitor ID code for remote control
3.REMOTE NO.
Setting the automatic/manual aspect ratio change as per
4.CHANGE ASPECT
reception channel
5.CONT VR ASSIGN
Setting the assignment of "CONT" manual control
Setting the backlight brightness level
6.BACKLIGHT DIM.
Setting the tally lamp display format
7.TALLY
Setting the same-size (dot-by-dot) display ON/OFF
8.REAL SCAN
9.SDI CH LOCK
Setting the SDI channel lock ON/OFF
Setting the SDI ERROR LED display ON/OFF
Setting the format display ON/OFF/TIMER at signal switching
1.SDI VITC
Setting the SDI VITC display ON/OFF
2.→DIMMER
Setting the SDI VITC display brightness
3.→SIZE
Setting the SDI VITC display size
4.WFM DISPLAY
Setting the waveform display ON/OFF
5.→DIMMER
Setting the waveform display brightness
6.→SIZE
Setting the waveform display size
7.→POSITION
Setting the waveform display position (right/center/left)
8.→COLOR
Setting the waveform display color (white/green)
9.VECTOR SCOPE
Setting the VECTOR SCOPE display ON/OFF
Setting the VECTOR SCOPE display brightness
Setting the VECTOR SCOPE display magnification ratio
Setting the COLOR BOX scale display (75%/100%)
Setting the VECTOR SCOPE display position (right/center/left)
Setting the VECTOR SCOPE display color (white/green)
1.SCR CAPTURE
Executing the 2-picture split mode
2.→AREA
Setting the 2-picture split mode display area
1.CHROMA GAIN UP
Setting the chroma gain -up ON/OFF
Setting the IP conversion mode (FIELD/FRAME)
2.IP MODE
3.H ＰOSITION
Adjusting the horizontal screen position
Adjusting the vertical screen position
4.V POSITION
Setting the contrast range (Normal/Wide)
5.CONTRAST RANGE
Setting the paired channels of embedded audio outputs
1.LINE/SP CH.
2.SP INPUT SEL
Setting the audio output singals
3.LEVEL INDICATOR
Setting the audio level meter display ON/OFF
Setting the audio level meter display mode
4.→MODE
Setting the audio level meter display channel
5.→CHANNEL
Setting the audio level meter display brightness
6.→DIMMER
Setting the audio level meter display peak hold
7.→PEAK HOLD
- -
10
Advertisement
Table of Contents
