D Auto Tuning Step Function; D ¼ Tuning Function; (Ssb Data/Cw/Rtty Only); D Band Edge Warning Beep - Icom IC-7200 Instruction Manual

D Auto tuning step function

When rotating the tuning dial rapidly, the tuning
speed accelerates automatically as selected.
MODE TS
TUNER FILTER
D ¼ tuning function (SSB data/CW/RTTY only)
While operating in SSB data/CW/RTTY, the ¼ tuning
function is available for critical tuning. Dial sensitivity
is reduced to ¼ of normal when the ¼ function is in
use.
MODE TS
TUNER FILTER

D Band edge warning beep

When selecting a frequency that lies outside of a
band's specified frequency range, a warning beep
sounds.
This function can be turned OFF in set mode, if de-
sired.
MODE TS
TUNER
FILTER
ANF
NB NR
METER
V/M 1 A/B 2 3
SPLIT
1.8 = 3.5 7
4 5 6
MW M-CL AGC
10 14 18
7 8 9
COMP SCAN VOX
21 24 28
.
0
MNF F-INP ENT
RIT
GENE
50 BAND
P.AMP
ATT
M-CH/RIT
SPCH
SET
[DIAL] [M-CH]
ANF
NB NR
METER
V/M 1 A/B 2 3
SPLIT
1.8 = 3.5 7
4 5 6
MW M-CL AGC
10 14 18
7 8 9
COMP SCAN VOX
21 24 28
.
0 F-INP ENT
RIT MNF
GENE 50
BAND
P.AMP
ATT
M-CH/RIT
SPCH
SET
[DIAL] [M-CH]
NB NR ANF
METER
V/M 1 A/B 2 3
SPLIT
1.8 = 3.5 7
4 5 6
MW M-CL AGC
10 14 18
7 8 9
COMP SCAN VOX
21 24 28
.
0
MNF F-INP ENT
RIT
GENE
50
BAND
P.AMP
ATT
M-CH/RIT
SPCH
SET
[DIAL] [M-CH]
M-CH/RIT
q Push and hold
SET
the set mode.
w Rotate [M-CH] to select "AUTo TS."
e Rotate [DIAL] to select the desired tuning speed
from HI (High), Lo (Low) and oF (OFF).
• HI : Approx. 5 times faster when the tuning step is set
to 1 kHz or smaller steps; approx. 2 times faster
when the tuning step is set to 5 kHz or larger steps.
• Lo : Approx. 2 times faster
• oF : Auto tuning step is turned OFF
• Push and hold for 1 sec. to select a default con-
M-CL
dition or value.
When "HI" is selected (default)
M-CH/RIT
r Push to exit the set mode and return to
SET
normal operation.
M-CH/RIT
q Push and hold
SET
the set mode.
w Rotate [M-CH] to select "DIAL ¼."
e Rotate [DIAL] to select the ¼ tuning function ON
and OFF.
• Push and hold for 1 sec. to select a default con-
M-CL
dition or value.
When "OFF" is selected (default)
M-CH/RIT
r Push to exit the set mode and return to
SET
normal operation.
NOTE: This function is only available when the
programmable tuning step is OFF (p. 26).
M-CH/RIT
q Push and hold
SET
the set mode.
w Rotate [M-CH] to select "BAND BEP."
e Rotate [DIAL] to select the band edge warning
beep function ON and OFF.
• Push and hold for 1 sec. to select a default con-
M-CL
dition or value.
When "ON" is selected (default)
M-CH/RIT
r Push to exit the set mode and return to
SET
normal operation.
BASIC OPERATION
for 1 sec. twice to enter
for 1 sec. twice to enter
for 1 sec. twice to enter
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
28