Xerox 6100BD - Phaser Color Laser Printer Manual page 4

Clean the Bindexer Sensors (Q1205, Q1206, Q1207)............................................................... 74
Clean the Bins Exit Sensors (Q1222)......................................................................................... 75
Clean the Front Stack (Q1227), Rear Stack Height (Q1218), and Set Path (Q1221) Sensors . 77
Clean the Fuser (Q1010) and Prefuser Sensors (Q1009) ......................................................... 80
Clean the Post Inverter (Q1202) and Output Transport (Q1203) Sensors ................................ 82
Clean the Pre-Fuser Sensor (Q1009) ........................................................................................ 84
Clean the Registration Transport Sensor (Q861)....................................................................... 85
Clean the Set Path Sensor (Q1221)........................................................................................... 86
Clean the Tape Binder Area ....................................................................................................... 89
Clear Paper Jams in Areas 11, 12, 13, and 14 .......................................................................... 91
Clear Paper Jams in Areas 11, 12, and 13 ................................................................................ 94
Clear Paper Jams in Areas 13, 14, and 15 ................................................................................ 97
Clear Paper Jams in Areas 17 and 18 ..................................................................................... 100
Clear the Entire Paper Path From the Paper Trays to the Finisher ......................................... 102
Clear the Fault in the Printer Fault Clearance Window ............................................................ 102
Clear the Paper Jam in Area 4 ................................................................................................. 103
Clear the Paper Jam in Areas 11, 14, 17, and 18 .................................................................... 103
Clear the Paper Jam in Areas 12, 13, 14, and 15 .................................................................... 107
Clear the Paper Jam in Areas 3 and 4 ..................................................................................... 111
Clear the Paper Jam in Areas 5 and 6 ..................................................................................... 112
Clear the Paper Jam in Areas 7, 6, and 5 ................................................................................ 113
Clear the Paper Jam in Areas 8 and 9 ..................................................................................... 115
Clear the Paper Jam in Areas 8, 11, 12, and 13 ...................................................................... 116
Clear the Paper Jams in Areas 16 and 17 ............................................................................... 119
Clear the Paper Jams in Areas 17 and 19 ............................................................................... 121
Clear the Paper Jams in Areas 7, 6, 5, 4, and 2 ...................................................................... 123
Clear the Stitcher A Fault ......................................................................................................... 125
Fan the Paper, Turn the Paper Over, and Reload ................................................................... 127
If Paper is Jammed in the Fuser, Release the Camming Motor Brake .................................... 127
If Printing to the Edges of the Paper Stock, set Lead Edge Screening to Stress .................... 128
If the Job is Sent From a DigiPath, Clean the Document Glass on the DigiPath..................... 129
Lower the Decurler Baffle Above Area 7 .................................................................................. 129
Open and Close the Area 3 and 4 Baffles Securely................................................................. 130
Open and Close the Area 4 Baffle Securely............................................................................. 130
Open and Close the Area 9 Baffle Securely............................................................................. 131
Open and Close the Finisher Top Cover and the Finisher Front Doors................................... 131
Perform an Immediate Shutdown at the DocuSP..................................................................... 132
Power OFF, Reset the Printer Circuit Breakers, Then Power ON ........................................... 132
Power OFF, Then Power ON the Printer.................................................................................. 133
Push Down on the Stacker Safety Door................................................................................... 134
Read the Meter......................................................................................................................... 135
Release the Camming Motor Brake ......................................................................................... 135
Remove Paper From Interposer Areas B1 and B2................................................................... 137
Reset the White Power Switch ................................................................................................. 138
Select Reset / Restart From the Fault Frame........................................................................... 138
Tap on the Toner (Dry Ink) Cartridge to Loosen the Toner...................................................... 139
Use A New Ream of Paper ...................................................................................................... 139
7. Perform Printer Functions............................................... 141
1. Add a Font to the DocuSP Controller .................................................................................. 142
2. Allow Main, Aux, Auto, or Unspecified to be Used as Stock Names .................................. 143
3. Backup VIPP Files Before an Upgrade ............................................................................... 144
4. Check the Systems Queue Output Location and Finishing Selections............................... 145
5. Clear the Faulted Job .......................................................................................................... 146
6. Create a New Queue........................................................................................................... 147
7. Delete a Job in Job Manager............................................................................................... 148
DT6180 HandyBook