Roland SonicCell User Manual page 201

24: FLANGER
This is a stereo flanger. (The LFO has the same phase for left
and right.) It produces a metallic resonance that rises and falls
like a jet airplane taking off or landing. A filter is provided so
that you can adjust the timbre of the flanged sound.
fig.MFX-24
Balance D
L in
Flanger
Feedback
Feedback
Flanger
R in
Balance D
Parameter Value
Filter Type OFF, LPF, HPF
Cutoff Freq
200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate # 0.05–10.00 Hz, note
Depth 0–127
Phase
0–180 deg
Feedback #
-98– +98%
Low Gain -15– +15 dB
High Gain -15– +15 dB
Balance # D100:0W–D0:100W
Level
0–127
25: STEP FLANGER
This is a flanger in which the flanger pitch changes in steps.
The speed at which the pitch changes can also be specified in
terms of a note-value of a specified tempo.
fig.MFX-25
Balance D
L in
Step Flanger
Feedback
Feedback
Step Flanger
R in
Balance D
Parameter Value
Filter Type OFF, LPF, HPF
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the flanger sound (W)
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Parameter Value
Cutoff Freq
200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate # 0.05–10.00 Hz, note
Depth 0–127
Phase
0–180 deg
Feedback # -98– +98%
Step Rate # 0.10–20.00 Hz, note
Low Gain -15– +15 dB
High Gain
-15– +15 dB
Balance # D100:0W–D0:100W
Level 0–127
26: HEXA-CHORUS
Uses a six-phase chorus (six layers of chorused sound) to give
richness and spatial spread to the sound.
fig.MFX-26
L in
Balance D
Hexa Chorus
R in
Balance D
Parameter Value
Pre Delay 0.0–100.0 ms
Rate #
0.05–10.00 Hz, note
Depth 0–127
Pre Delay
0–20
Deviation
Depth
-20– +20
Deviation
Pan Deviation 0–20
Balance #
D100:0W–D0:100W
Level 0–127
Effects List
Description
Basic frequency of the filter
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Rate (period) of pitch change
Gain of the low range
Gain of the high range
Volume balance between the di-
rect sound (D) and the flanger
sound (W)
Output Level
L out
Balance W
Balance W
R out
Description
Adjusts the delay time from the di-
rect sound until the chorus sound is
heard.
Frequency of modulation
Depth of modulation
Adjusts the differences in Pre Delay
between each chorus sound.
Adjusts the difference in modulation
depth between each chorus sound.
Adjusts the difference in stereo loca-
tion between each chorus sound.
0: All chorus sounds will be in the
center.
20: Each chorus sound will be
spaced at 60 degree intervals
relative to the center.
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level
201