Lenovo ThinkSystem SD530 V3 User Manual page 174

After this task is completed
1. If necessary, install the rear I/O module and rear OCP cable to the node (see
on page 150 and "Install a power distribution board" on page
module and OCP cable to the system board (see
179).
2. If necessary, install the power distribution board and connect cables between the power distribution
board and the system board (see
distribution board cable routing" on page
3. Reinstall the power bus bar (see
4. If necessary, reinstall the PCIe riser assembly to the node and reconnect the required PCIe cables to the
system board (see "Install a PCIe riser assembly" on page 121
page 173).
5. If necessary, reinstall the GPU air duct (see
6. Reinstall the required M.2 drives to the system board (see
7. Reinstall the MicroSD card to the system board (see
8. Reinstall the firmware and RoT security module to the system board (see
security module" on page
9. Reinstall all the required memory modules or memory module fillers (see
page 107).
10. If there is no CMOS battery (CR2032) installed on the system board yet, install one (see
battery (CR2032)" on page
11. Reconnect all the required cables to the system board (see
173).
12. Reconnect all the required cables to the drive backplane; then, reinstall the drive cage assembly to the
node (see "E3.S drive backplane cable routing" on page 176
page 88).
13. Reinstall the required processor and heat sink modules (PHMs) (see
on page 137).
14. Make sure that all the required cables are routed and connected correctly; then, reinstall the top cover
(see "Install the top cover" on page
15. Reinstall the node into the chassis (see
16. Make sure that the required power supply units are installed and power cords are connected; then,
power on the node (see
51.)
17. Proceed to complete the parts replacement (see
18. Update the vital product data (VPD). See
type number and serial number can be found on the ID label, see
Lenovo XClarity Controller" on page
19. If hiding TPM or updating TPM firmware is needed, see
the TPM firmware" on page
20. Optionally, enable UEFI Secure Boot. See
21. Download and install the latest device drivers:
thinksystem/sd530v3/7dd3/downloads/driver-list
22. Update the system and device firmware. See
Note: (Lenovo trained technician only) If you have replaced the firmware and RoT security module,
update the firmware to the specific version supported by the server. See
ThinkSystem SD530 V3 User Guide
164
"Install a power distribution board" on page 129
179).
"Install a power bus bar" on page
"Install a GPU air duct" on page
153).
82).
170).
"Install a node to the chassis" on page
"Install a hot-swap power supply" on page 61
"Update the Vital Product Data (VPD)" on page
35.
167.
"Enable UEFI Secure Boot" on page
https://datacentersupport.lenovo.com/products/servers/
.
"Update the firmware" on page
129); then, connect cables of the rear I/O
"Rear I/O and OCP module cable routing" on page
125).
and Chapter 6 "Internal cable routing" on
"Install an M.2 drive" on page
"Install a MicroSD card" on page
Chapter 6 "Internal cable routing" on page
and "Install a drive cage assembly" on
"Install a processor and heat sink"
and
"Complete the parts replacement" on page
"Identify the system and access the
"Hide/observe TPM" on page 166
"Install a rear I/O module"
and "Power
93).
103).
112).
"Install a firmware and RoT
"Install a memory module" on
"Install a CMOS
75).
"Power on the node" on page
171).
165. Machine
or "Update
168.
185.
https://