Management Tunneling Hub Configuration; Figure 4-14 Management Tunneling Hub Configuration Screen - Zhone 100 User Manual

4 Operation
Management
Tunneling Hub
Configuration

******************** Management Tunneling Hub Configuration ********************

Name: F@43802
Management Tunnels
--- DLCI,IP ADD ---
[T1=]:0.0.0.0.0
[T2=]:0.0.0.0.0
[T3=]:0.0.0.0.0
[T4=]:0.0.0.0.0
[T5=]:0.0.0.0.0
[T6=]:0.0.0.0.0
[T7=]:0.0.0.0.0
[T8=]:0.0.0.0.0
[T9=]:0.0.0.0.0
[T10=]:0.0.0.0.0
[T11=]:0.0.0.0.0
[T12=]:0.0.0.0.0
[T13=]:0.0.0.0.0
[T14=]:0.0.0.0.0
[T15=]:0.0.0.0.0
[T16=]:0.0.0.0.0
Help?]
>

Figure 4-14 Management Tunneling Hub Configuration Screen

4-28
The Management Tunneling Hub Configuration Screen allows you to view and alter
parameters for Management Tunneling Hub operations.
The Management Tunneling Hub Configuration Screen is shown in Figure 4-14.
Hub DLCI [D=#]: Disabled
X to Disable or 16 thru 991
[T17=]:0.0.0.0.0
[T18=]:0.0.0.0.0
[T19=]:0.0.0.0.0
[T20=]:0.0.0.0.0
[T21=]:0.0.0.0.0
[T22=]:0.0.0.0.0
[T23=]:0.0.0.0.0
[T24=]:0.0.0.0.0
[T25=]:0.0.0.0.0
[T26=]:0.0.0.0.0
[T27=]:0.0.0.0.0
[T28=]:0.0.0.0.0
[T29=]:0.0.0.0.0
[T30=]:0.0.0.0.0
[T31=]:0.0.0.0.0
[T32=]:0.0.0.0.0
Save[SA] Cancel[X]
1. Hub DLCI - Sets or disables the private network PVC for WAN management of
multiple remote units via this unit as a central Hub (Management Tunneling Hub.)
2. IP Encap - Select the type of IP encapsulation to be used for management traffic
within the PVC between the Central Router and the Hub. Selections are:
Raw - No protocol specified. Data (user's payload) is encapsulated only by the
frame of the Frame Relay packet.
IETF - Protocol will be specified by its own NLPID.
3. Management Tunnels - DLCI,IP ADD - Each 19-character entry specifies the
routing (mapping) of packets through the Management Tunneling Hub.
The first (left-most) decimal number indicates the DLCI identifying the PVC on
which the remote unit is located.
The remaining four decimal numbers indicate the management IP address of the
remote unit.
Commands:
Help [?] - Advances to "Help" for Management Tunneling Hub Configuration screen.
Save [SA] - Saves parameters and returns to System View screen.
Cancel [X] - Returns to System View screen without saving changes.
Save the Management Tunneling Hub Configuration changes when they are all set cor-
rectly by entering "SA" followed by ENTER. Also returns the user to the System View
screen.
NetPath 100 User's Manual - Installation Guide
--- DLCI,IP ADD ---
[T33=]:0.0.0.0.0
[T34=]:0.0.0.0.0
[T35=]:0.0.0.0.0
[T36=]:0.0.0.0.0
[T37=]:0.0.0.0.0
[T38=]:0.0.0.0.0
[T39=]:0.0.0.0.0
[T40=]:0.0.0.0.0
[T41=]:0.0.0.0.0
[T42=]:0.0.0.0.0
[T43=]:0.0.0.0.0
[T44=]:0.0.0.0.0
[T45=]:0.0.0.0.0
[T46=]:0.0.0.0.0
[T47=]:0.0.0.0.0
[T48=]:0.0.0.0.0
IP Encap [E=]
>>1) Raw<<
2) IETF
--- DLCI,IP ADD ---
980-001-0210G
June 1999