Table of Contents
Advertisement
Note: If you do not specify any of these parameters, ASU will use the default values. When the
default values are used and ASU is unable to access the IMM using the online authenticated
LAN access method, ASU will automatically use the following unauthenticated KCS access
method.
The following commands are examples of using the userid and password default values and not
using the default values:
Examples that do not use the userid and password default values:
asu set SYSTEM_PROD_DATA.SysInfoProdName <m/t_model>
--user <imm_user_id> --password <imm_password>asu set SYSTEM_PROD_DATA.SysInfoProdIdentifier <system m
--user <imm_user_id> --password <imm_password>asu set SYSTEM_PROD_DATA.SysInfoSerialNum <s/n> --user
--password <imm_password>asu set SYSTEM_PROD_DATA.SysEncloseAssetTag <asset_tag>
--user <imm_user_id> --password <imm_password>
Examples that do use the userid and password default values:
asu set SYSTEM_PROD_DATA.SysInfoProdName <m/t_model>asu set SYSTEM_PROD_DATA.SysInfoProdIdentifier <s
• Online KCS access (unauthenticated and user restricted): You do not need to specify a value for
access_method when you use this access method.
The KCS access method uses the IPMI/KCS interface. This method requires that the IPMI driver
be installed. Some operating systems have the IPMI driver installed by default. ASU provides the
corresponding mapping layer. See the Advanced Settings Utility Users Guide at
www.ibm.com/support/entry/portal/docdisplay?lndocid=TOOL-ASU
The following commands are examples of using the userid and password default values and not
using the default values:
Examples that do not use the userid and password default values:
asu set SYSTEM_PROD_DATA.SysInfoProdName <m/t_model>asu set SYSTEM_PROD_DATA.SysInfoProdIdentifier <s
• Remote LAN access, type the command:
Note: When using the remote LAN access method to access IMM using the LAN from a client,
the host and the imm_external_ip address are required parameters.
host <imm_external_ip> [user <imm_user_id>][password <imm_password>]
Where:
imm_external_ip
The external IMM LAN IP address. There is no default value. This parameter is required.
imm_user_id
The IMM account (1 of 12 accounts). The default value is USERID.
imm_password
The IMM account password (1 of 12 accounts). The default value is PASSW0RD (with a zero
0 not an O).
The following commands are examples of using the userid and password default values and not
using the default values:
Examples that do not use the userid and password default values:
asu set SYSTEM_PROD_DATA.SysInfoProdName <m/t_model> --host <imm_ip>
--user <imm_user_id> --password <imm_password>asu set SYSTEM_PROD_DATA.SysInfoProdIdentifier <system m
--user <imm_user_id> --password <imm_password>asu set SYSTEM_PROD_DATA.SysInfoSerialNum <s/n> --host
--user <imm_user_id> --password <imm_password>asu set SYSTEM_PROD_DATA.SysEncloseAssetTag <asset_tag
--user <imm_user_id> --password <imm_password>
Examples that do use the userid and password default values:
asu set SYSTEM_PROD_DATA.SysInfoProdName <m/t_model> --host <imm_ip>asu set SYSTEM_PROD_DATA.SysInfo
for more details.
.
Chapter 6
Configuration information and instructions
http://
533
Advertisement
Table of Contents
