Oki LP-1040 Maintenance Manual page 198

Error
No.
JAM 3593 The tail edge of the
paper is not
disengaging from
the PS05 position
even after the
estimated paper
pass-through time is
exceeded.
JAM 3594 The tail edge of the
paper is not
disengaging from
the PS05 position
even after the
estimated paper
pass-through time is
exceeded.
JAM 3601 The lead edge of
the paper is
reaching PS06 too
quickly.
JAM 3602 The lead edge of
the paper is
reaching PS06 too
quickly.
JAM 3603 The lead edge of
the paper is not
reaching PS06.
JAM 3604 The lead edge of
the paper is not
reaching PS06.
5-24
Cause User Solution
- Remove the paper particles
following the operation panel
indication.
- Check that the paper flange is
fixed.
- Check that the paper flange is
installed on the flange guide
properly.
- When the paper head edge is
bent, folded, or burred, cut
the paper edge.
- Check that the roll paper is
installed properly (see the
User's Manual for Basic
Printer Operation,
Replacing the Roll Paper).
- Install the OKI DATA
INFOTECH official paper, or
replace the current roll paper
(see the User's Manual for
Basic Printer Operation).
- Restart the printer.
ditto
ditto
ditto
ditto
ditto
Service Engineer Inspection
(For inspection criteria, see
Reference to Check/Replace
Parts.)
- Check that no paper
particle is found on PS05.
- Check that no problem is
found with the cutting
condition at the paper tail
edge. Perform 3042-3047
problem analysis.
- Check PS05 for On/Off
setting.
- Check CBL-MECH2 and
CBL-PS04 for short circuit.
- Check that PS05 is
installed securely and its
lever functions normally.
- Check the CL04 operation.
- Check paper delivery path
after PS05.
- Check the pinch roller
pressure.
- Check the motor TM01
operation.
- Check PCB-ASSY-AAC.
ditto
- Check that no problem is
found with the cutting
condition at the paper tail
edge. Perform 3042-3047
problem analysis.
- Check that PS06 is
installed securely and its
lever functions normally.
- Check that CL04 if installed
securely and operates
normally.
ditto
- Check that the paper and
paper flange are installed
properly.
- Check that no problem is
found with the cutting
condition at the paper tail
edge. Perform 3042-3047
problem analysis.
- Check PS06 for On/Off
setting.
- Check CBL-FUSER21 and
-22 and CBL-PS06 for
short circuit.
- Check that PS06 is
installed securely and its
lever functions normally.
- Check the paper delivery
path.
- Check that the belt is
extended.
- Check that the paper is not
bubbled.
- Check that the paper is
separated from the drum.
- Check the BL01 operation.
- Check the ozone filter.
ditto
Reference to
Assumed
Check/Replace
Replacement Part
Parts
 P. 5-34 (11)
- PS05
 P. 9-149
- Cutter unit
 P. 9-32
- PCB-ASSY-ARC
 P. 9-55
- PCB-ASSY-AAC
 P. 9-54
- Motor (TM01)
 P. 9-133
- CL04
 P. 9-45
ditto ditto
 P. 5-34 (12)
- PS06
 P. 9-224
- Cutter unit
 P. 9-32
- PCB-ASSY-ARC
 P. 9-55
- PCB-ASSY-AAC
 P. 9-54
- CL04
 P. 9-45
ditto ditto
 P. 5-35 (13)
- PS06
 P. 9-224
- Cutter unit
 P. 9-32
- PCB-ASSY-ARC
 P. 9-55
- PCB-ASSY-AAC
 P. 9-54
- BL01
 P. 9-78
- Ozone filter
- CBL-FUSER21/
22
- CBL-PS06
ditto ditto