Table of Contents
Advertisement
Parameter Name
Parameter
Addr.
Digital Operator
No.
Hex
d1-01
Set-point Reference 1
0280
Set-point 1
d1-02
Set-point Reference 2
0281
Set-point 2
d1-03
Set-point Reference 3
0282
Set-point 3
d1-04
Set-point Reference 4
0283
Set-point 4
d1-17
Jog Frequency Reference
0292
Jog Reference
Denotes that parameter can be changed when the drive is running.
Frequency Reference
d2-01
0289
Upper Limit
Ref Upper Limit
Frequency Reference
d2-02
028A
Lower Limit
Ref Lower Limit
Master Speed Reference
d2-03
0293
Lower Limit
Ref1 Lower Limit
Jump Frequency 1
d3-01
0294
Jump Freq 1
Jump Frequency 2
d3-02
0295
Jump Freq 2
Jump Frequency 3
d3-03
0296
Jump Freq 3
Jump Frequency Width
d3-04
0297
Jump Bandwidth
Input Voltage Setting
E1-01
0300
Input Voltage
V/f Pattern Selection
E1-03
0302
V/f Selection
56
Display
Digital preset setpoint reference 1. Used when b1-01 = 0 and when in
"hand" mode. Setting units are affected by P1-02.
Digital preset setpoint reference 2. Selected via multi-function input
terminals. Setting units are affected by P1-02.
Parameter d1-02 is also the Zone 1 PI reference when b5-01 = 2.
Digital preset setpoint reference 3. Selected via multi-function input
terminals. Setting units are affected by P1-02.
Parameter d1-03 is also the Zone 2 PI reference when b5-01 = 2.
Digital preset setpoint reference 4. Selected via multi-function input
terminals. Setting units are affected by P1-02.
Parameter d1-04 is also the Zone 1 and 2 PI reference when b5-01 = 2.
<0034>
Jog reference used when a jog is selected via the LCD operator keypad.
This parameter is not available with the HOA operator. Setting units are
affected by o1-03.
Determines maximum speed command, set as a percentage of parameter
E1-04. If speed command is above this value, actual drive speed will be
limited to this value. This parameter applies to all speed command sources.
Determines minimum speed command, set as a percentage of parameter
E1-04. If speed command is below this value, actual drive speed will be set
to this value. This parameter applies to all speed command sources.
Determines the minimum speed command, set as a percentage of
parameter E1-04. If speed command is below this value, actual drive speed
will be set to this value. This parameter only applies
to analog inputs A1 and A2.
These parameters allow programming of up to three prohibited frequency
points for eliminating problems with resonant vibration of the motor/
machine. This feature does not actually eliminate the selected frequency
values, but will accelerate and decelerate the motor through the prohibited
bandwidth.
This parameter determines the width of the deadband around each selected
prohibited frequency point. A setting of "1.0" will result in a deadband of
+/- 1.0 Hz.
Set to the nominal voltage of the incoming line.
0: 50 Hz
1: 60 Hz Saturation
2: 50 Hz Saturation
3: 72 Hz
4: 50 Hz VT1
5: 50 Hz VT2
6: 60 Hz VT1
7: 60 Hz VT2
8: 50 Hz HST1
9: 50 Hz HST2
A: 60 Hz HST1
B: 60 Hz HST2
C: 90 Hz
D: 120 Hz
F: Custom V/F
FF: Custom w/o limit
Description
Preset Reference
Reference Limits
Jump Frequencies
V/f Pattern
Setting
Factory
Range
Setting
0.00
0.00
<0034>
1 ~ P1-03
Value
0.00
0.00 to
<0034>
P1-02
Value
<0034>
0.00
0.00
0.0 ~
100.0 %
110.0 %
0.0 ~
0.0 %
110.0 %
0.0 ~
0.0 %
110.0 %
0.0 Hz
0.0 ~
0.0 Hz
200.0 Hz
0.0 Hz
0.0 ~
1.0 Hz
20.0 Hz
155 ~
255.0
240 V
(240V)
310 to
480 V
510.0
(480V)
0 ~ FF
F
YASKAWA TM.iQp.10 Technical Manual Supplement
Menu
Location
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Programming
Advertisement
Table of Contents
