Scan; Numeric Parameter Settings (Numeric Prama.) - Canon imageRUNNER 1750 Series Service Manual

■ Numeric Parameter Settings (Numeric Prama.)

● 033Vertical scan magnification correction
Correct the magnification of vertical scanning of a book. The larger the adjustment value, the
more the image stretches in the vertical scanning direction.
● 034: Horizontal scan magnification correction
Correct the magnification of horizontal scanning of a book. The larger the adjustment value,
the more the image stretches in the horizontal scanning direction.
● 047: Vertical scan magnification correction (when scanning on a
document fed from ADF)
Correct the magnification of vertical scanning of a document fed from the ADF. The larger the
adjustment value, the more the image stretches in the vertical scanning direction.
● 048: Horizontal scan magnification correction (when scanning on a
document fed from ADF)
Correct the magnification of horizontal scanning of a document fed from the ADF. The smaller
the adjustment value, the more the image stretches in the horizontal scanning direction.
● 135: Leading edge trimming length when performing fax operation
using the Copyboard (0.1 mm)
As the value is incremented by "1", the leading edge non-image width is increased by 0.1mm.
● 138: Leading edge frame length when performing copy operation
using the Copyboard (0.1 mm)
As the value is incremented by 1, the image position moves to the trailing edge side by 0.1mm.
● 145: Leading edge trimming length when performing fax operation
using the ADF (0.1 mm)
As the value is incremented by "1", the leading edge non-image width is increased by 0.1mm.
● 146: Trailing edge trimming length when performing fax operation
using the ADF (0.1 mm)
As the value is incremented by "1", the trailing edge non-image width is increased by 0.1mm.
● 147: Left-right frame length when performing fax operation using the
ADF (0.1 mm)
As the value is incremented by 1, the image position moves to the right edge side by 0.1mm.
8
Service Mode > Details of Service Mode > #SCAN > Numeric Parameter Settings (Numeric Prama.)
8 Service Mode > Details of Service Mode > #SCAN > Numeric Parameter Settings (Numeric Prama.)
● 148: Leading edge frame length when performing copy operation
using the ADF (0.1 mm)
As the value is incremented by 1, the image position moves to the trailing edge side by 0.1mm.
● 165: Leading edge frame length when performing SEND SCAN using
the Copyboard (0.1 mm)
As the value is incremented by 1, the image position moves to the trailing edge side by 0.1mm.
● 168: Leading edge frame length when performing SEND SCAN using
the ADF (0.1 mm)
As the value is incremented by 1, the image position moves to the trailing edge side by 0.1mm.
● 193: ADF special standard-sized paper: LGL misidentification-ready
Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because
it is misidentified as "LEGAL").
0 : LEGAL 1 : FOOLSCAP 2 : M_OFICIO 3 : A_FOOLSCAP 4 : FOLIO
5 : G_LEGAL 7 : B_OFICIO 8 : OFICIO
To enable the change in this service mode, the following settings need to be changed:
#SCAN > #SCAN SW > SW05,
#SYSTEM > #SYSTEM SW > SW57
When 1 to 5, 7 to 9 are set
#SCAN > #SCAN SW > SW05
#SYSTEM > #SYSTEM SW > SW57
When 10 is set
#SCAN > #SCAN SW > SW05
#SYSTEM > #SYSTEM SW > SW57
8-26
9 : E_OFICIO 10 : F4A
2 (Inch configuration)
2 (Inch configuration)
0 or 1 (A configuration, AB configuration)
1 or 0 (A configuration, AB configuration)
8-26