Table 29: Module 765-1505/100-000 - Currents In Supply Cable 1; Table 30: Module 765-1505/100-000 - Currents In Supply Cable 2 - WAGO 765-1505/100-000 Product Manual

Planning
Pin
4
The device is designed in such a way that it can be used in overload operation according
to the following table "Module 765-1505/100-000 – Currents in Supply Cable 1" without
time limit. The following applies to all pins:
If the maximum load capacity (upper limit of overload operation) of the pin is exceeded,
there is a risk of destruction of or damage to the pluggable connector or PCB of the de-
vice.
CAUTION
Note significance of pin 3
Note that the sum of the currents of pins 1 and 4 flows to pin 3.
Product-Specific Information
For supply cable 1L of the 765-1505/100-000 Digital Input/Output Module, the currents
declared in the following table must be taken into account:
Current
I
X31_1L
I
X32_1L
I
logic
I ,
X01_1L
I ,
X02_1L
I
module_1L
For supply cable 2L of the 765-1505/100-000 Digital Input/Output Module, the currents
declared in the following table must be taken into account:
Current
I
X31_2L
I
X32_2L
I ,
X05_2L
I ,
X06_2L
I
module_2L
During operation of the 765-1505/100-000 Digital Input/Output Module requires, the rules
below for the currents in supply cables 1 and 2 must be followed at all times:
38 Product manual | Version: 2.0.0
8DIO FLD EI DC 24V 2.0A
I
... , X04_1L
I
... , X08_2L
Normal Operation
2 A
Table 29: Module 765-1505/100-000 – Currents in Supply Cable 1
Description
Current to connection PWR IN (X31): current 1L+ / reverse current 1L−
Current to connection PWR OUT (X32): current 1L+ / reverse current 1L−
Logic supply
Total current for supply cable 1 at digital input/output X0i (i.e., port X01,
X02, ... , X04); corresponds to current I
current is the sum of the currents at pins 1 and 4 of digital input/output
X0i:
I = I = I + I
X0i_1L X0i_pin3_1L X0i_pin1_1L X0i_pin4_1L
Module current I I
module_1L = X01_pin3_1L
Table 30: Module 765-1505/100-000 – Currents in Supply Cable 2
Description
Current to connection PWR IN (X31): current 2L+ / reverse current 2L−
Current to connection PWR OUT (X32): current 2L+ / reverse current 2L−
Total current for supply cable 2 at digital input/output X0i (i.e., port X05,
X06, ... , X08); corresponds to current I
current is the sum of the currents at pins 1 and 4 of digital input/output
X0i:
I = I = I + I
X0i_2L X0i_pin3_2L X0i_pin1_2L X0i_pin4_2L
Module current I I
module_2L = X05_pin3_2L
765-1505/100-000
Overload Operation
2.4 A
on pin 3 (ground). This
X0i_pin3_1L
su
+ I + I + I
X02_pin3_1L X03_pin3_1L X04_pin3_1L
on pin 3 (ground). This
X0i_pin3_2L
su
+ I + I + I
X06_pin3_2L X07_pin3_2L X08_pin3_2L