Page 1
WAGO I/O System Field 16-Channel Digital Output; EtherNet/IP; 24 V DC; 2.0 A; 8 × M12 Connection 765-1503/100-000 Product manual | Version 2.0.0...
Page 2
We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent. WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
765-1503/100-000 Table of Contents Table of Contents Provisions......................... 7 Intended Use ...................... 7 Typographical Conventions.................. 8 Legal Information .................... 9 Safety .......................... 11 General Safety Rules .................... 11 Electrical Safety..................... 11 Mechanical Safety .................... 11 Thermal Safety ...................... 11 Indirect Safety ....................... 12 Overview ......................... 13...
Page 4
Table of Contents 765-1503/100-000 Overload protection .................... 27 Parameterization Tools .................. 27 Overview ...................... 27 5.5.1 WAGO Webserver I/O Field ................. 29 5.5.2 WAGO I/O Field app .................. 30 5.5.3 Communication Interfaces.................. 31 EtherNet/IP .................... 31 5.6.1 OPC UA Server .................... 32 5.6.2...
Page 5
10.3.1.4.8 Forcing Digital Inputs and Outputs .......... 74 WAGO I/O Field app .................. 76 10.3.2 10.3.2.1 Parameterizing a Module with the WAGO I/O Field App ..... 76 OPC UA Server .................... 76 10.3.3 10.3.3.1 Parameterizing the Product via OPC UA.......... 77 10.3.3.1.1 Identifying Devices..............
Page 6
Table of Contents 765-1503/100-000 Appendix........................ 105 14.1 Installation Regulations Specified by Approvals .......... 105 14.2 Operational Description.................. 106 14.3 Protected Rights.................... 108 Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
The terms set forth in the General Business and Contract Conditions for Delivery and Service of WAGO GmbH & Co. KG and the terms for software products and products with integrated software stated in the WAGO Software License Contract – both available at ü www.wago.com...
Provisions 765-1503/100-000 Individual agreements always have priority. Obligations of Installers/Operators The installers and operators bear responsibility for the safety of an installation or a sys- tem assembled with the products. The installer/operator is responsible for proper installa- tion and safety of the system. All laws, standards, guidelines, local regulations and ac- cepted technology standards and practices applicable at the time of installation, and the instructions in the the products’...
Page 9
765-1503/100-000 Provisions Figures Figures in this documentation are for better understanding and may differ from the actual product design. Notes DANGER Type and source of hazard Possible consequences of hazard that also include death or irreversible injury • Action step to reduce risk...
Page 10
Provisions 765-1503/100-000 without any reference to patent rights. WAGO GmbH & Co. KG, or for third-party prod- ucts, their manufacturer, retain all rights regarding patent, utility model or design registra- tion. ® Third-party trademarks are referred to in the product documentation. The “...
765-1503/100-000 Safety Safety 2.1 General Safety Rules • This documentation is part of the product. Therefore, retain the documentation during the entire service life of the product. Pass on the documentation to any subsequent user of the product. In addition, ensure that any supplement to this documentation is included, if necessary.
In addition, note the information on the product housing and further infor- mation, e.g. at ü www.wago.com/<item number>. • Only permit skilled personnel approved by WAGO to perform repair work. Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Overview Overview The product is part of the WAGO I/O System Field 765. It is intended for industrial use within an ETHERNET network and communicates with a central controller and/or directly with the control level, if necessary. Several sensors/actuators can be connected to the product for connection in the field level.
765-1503/100-000 Properties Function Position Custom Name Description LNK (X21) Link LED for port X21 ACT (X21) Activity LED for port X21 ETHERNET interface, M12, D-coded, EtherNet/IP port 2 LNK (X22) Link LED for port X22 ACT (X22) Activity LED for port X22 ®...
Properties 765-1503/100-000 Table 2: Supply Voltage Supply Voltage In- Supply Voltage Signal Description Output 24 VDC supply voltage U for system and sensor/actuator 2L− Reference potential for 2L 1L− Reference potential for 1L 24 VDC auxiliary/control voltage U Functional ground M12, L-coded, plug,...
765-1503/100-000 Properties 4.3 Circuit Diagram The following figure shows the schematic circuit diagram of the product. Figure 2: Circuit Diagram for Each Port 4.4 Technical data 4.4.1 Product Table 5: Product Property Value Item Number 765-1503/100-000 Product function 16-channel digital output Product name (short) 16 DO FLD EI 24 VDC 2.0 A...
765-1503/100-000 Properties Parameters Value Value (per UL) Current consumption of supply connections Max. 16 A; ensure external External fuses in lines 1L limitation or use fuses in and 2L: max. 16 A, time- the cables delay, min. 30 VDC The maximum total current...
Properties 765-1503/100-000 Property Value Value (per UL) Pollution degree 3 (EN 60664-1) Operating altitude 0 ... 2000 m Overvoltage category II (EN 60664-1) Protection type IP67 (EN 60529) Indoor use (enclosure type 12, 13; IP67) Protection class III (EN 61140) Vibration resistance 5g (IEC 60068-2-6) Shock resistance 50g (IEC 60068-2-27) 4.4.7 Communication...
The product provides measured values for temperature and current, which you can display with WAGO Webserver I/O Field or read out via OPC UA. The following figure shows the maximum permissible current (I) that can flow into the product as a function of the surrounding air temperature (T).
Properties 765-1503/100-000 Figure 4: Derating of a Contact (Pin) of L-Coded Connections X31 and X32 (For Core Cross-Section = 0.25 mm /AWG 14) Also note the derating curve for the individual contacts (pins) of the A-coded connections port X01, X02 etc. The following figure shows the maximum permissible current (I) that can flow through the contact (pin) as a function of the ambient temperature (T).
765-1503/100-000 Properties 4.7 Approvals The following approvals have been granted for the product: Conformity marking UL 61010-1 and UL 61010-2-201, “Ordinary Pending Location” ® Bluetooth This module has an RF transmitter with the following specifica- tions: • Operating frequency: 2402–2480 MHz •...
Functions 765-1503/100-000 Functions 5.1 Process Image This section describes the process data. The structure of the process data depends on which connection (connection 1, connection 2 etc.) is used between the EtherNet/IP scanner and the module. The module offers multiple connections; a connection was se- lected during configuration of the EtherNet/IP scanner.
765-1503/100-000 Functions Table 20: Process Data of the Digital Inputs (Pin-Based Assignment) Byte Off- Input Process Data Port X01, pin 4: DI A or mirrored DO A Port X02, pin 4: DI A or mirrored DO A Port X07, pin 4: DI A or mirrored DO A Port X08, pin 4: DI A or mirrored DO A Port X01, pin 2: DI B or mirrored DO B...
The “Forcing” function can be accessed through the following tools: • WAGO I/O Field Webserver • WAGO I/O Field app on mobile devices Systems like SPS, TIA Portal and the like also have forcing functions. Such forcing func- tions should not be confused with the ones described in this section and will not be con- sidered within the context of this section.
The measurements are performed for the module and for pin 1, pin 2 and pin 4 of each port. The measured values can be displayed in the WAGO I/O Field Webserver or the WAGO I/O Field app. Alternatively, an OPC UA client can read out the measured values and display them.
Series module. With a Web browser, users can view the Web pages and display and modify parameters. WAGO I/O Field App The WAGO I/O Field app is an app for mobile devices that can communicate with ® a 765 Series module via Bluetooth .
WAGO I/O Field app or the OPC UA client are overwritten. If you have changed parameters of the port configuration via the WAGO I/O Field Web- server, WAGO I/O Field App, the WAGO IO-Link Configurator or the OPC UA client, please note that these changes are initially applied by the module, but the Ethernet/IP scanner overwrites the port configuration again at the next start-up.
The functional scope described can vary depending on the module type. 5.5.3 WAGO I/O Field app The WAGO I/O Field app is an app for maintenance, diagnostics, operation and monitor- ing of installed WAGO I/O System Field modules and IO-Link devices.
You can find Product-specific information on the WAGO App I/O Field in the online help for the app. An iOS version of the WAGO I/O Field app is available for free in the Apple App Store, and an Android version in the Google Play Store.
Functions 765-1503/100-000 5.6.2 OPC UA Server The module has an integrated OPC UA server. Function Overview • Read module identification • Read configuration • Read measured values: current, voltage, temperature • Events: overcurrent, overload and overtemperature • Read status information •...
• Do not connect control components and control networks to an open network such as the Internet or an office network. WAGO recommends putting control components and control networks behind a fire- wall. • In the control components, close all ports and services not required by your application to minimize the risk of cyber attacks and to enhance cybersecurity.
Greater shielding performance is achieved via low-impedance connection between shielding and ground. For this purpose, connect the shielding over a large surface area, e.g., using the WAGO 790 Shield Connection System. This is especially recom- mended for large-scale systems where equalizing or high impulse currents may occur.
Page 35
765-1503/100-000 Planning Consumption For each supply cable, it is necessary to take into account the consumption that depends on the connected devices. Supply Cable 1: • Logic supply (about 200 mA) • Power supply of all connected sensors/actuators via 1L • Power supply of successive devices via 1L Supply Cable 2: •...
Planning 765-1503/100-000 An upper limit of 16 A applies to the total current in a supply cable. If this upper limit is ex- ceeded, there is a risk of destruction of or damage to the module. To avoid this, protect each supply line with a fuse or circuit breaker. In connection with this, also read section 8 Requirements on the Power Supply...
Note that the sum of the currents of pins 2 and 4 flows to pin 3. Product-Specific Information For supply line 1 of the 765-1503/100-000 Digital Output Module, the currents declared in the following table must be taken into account: Table 28: Module 765-1503/100-000 –...
Planning 765-1503/100-000 Current Supply Cable 1 Supply Line 2 Ports Ports X01, ... , X08 (henceforth summarized as port X0i for 1 ≤ i ≤ 8) Supply current on pin 1 (rule 3) ≤ 4 A X0i_pin1_2L Signal current on pin 2/4 in normal ≤...
• Power supply group via PWR OUT connection (with calculation of the permissible cur- rent feedthrough) Example of Individual Power Supply This example considers a single 765-1503/100-000 module where no additional devices are powered through its PWR OUT connection (X32). Product manual | Version: 2.0.0...
Page 40
Planning 765-1503/100-000 Figure 6: Connection Example with Individual Power Supply (Module Image May Vary) One digital input/output with a current consumption of max. 2 A is connected to ports X01 through X04 of the module. The module’s current consumption is 0.2 A. Supply cable 1 then has a total current consumption of 2 × 2 A + 0.2 A = 4.2 A, and sup- ply cable 2 has a total current consumption of 2 ×...
WAGO I/O Field app. ® 1: Disable bluetooth The Bluetooth interface cannot be enabled by an optical signal of a mobile device and in connection with the WAGO I/O Field app. Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Planning 765-1503/100-000 Parametername Value Range Default Description ® Bluetooth timeout 6 ... 59 [s] Switch-off time of the Bluetooth interface if not used; ® a new Bluetooth connection can be estab- lished by an optical signal after the Blue- ®...
765-1503/100-000 Transport and Storage Transport and Storage The original packaging offers optimal protection during transport and storage. • Store the product in suitable packaging, preferably the original packaging. • Only transport the product in suitable containers/packaging. • Make sure the product contacts are not contaminated or damaged during packing or unpacking.
Installation and Removal 765-1503/100-000 Installation and Removal 8.1 Installation 8.1.1 Tools Required for Installation The following tools are required for installation: • Allen wrench for the M4 hex head mounting screws The following additional items are only required for installation where no threaded hole is present: •...
765-1503/100-000 Installation and Removal • When mounting, be sure not to contaminate the connections. The contamination dam- ages the contacts, which can limit the reliability of the contacts. 8.1.4 Note on Protecting against Heat Generation by the Product During operation, the product can get hot! Therefore, always note the following informa- tion: •...
Installation and Removal 765-1503/100-000 8.1.8 Grounding Functional Ground The L-coded M12 pluggable connectors of the product’s power supply have one FE (functional ground) pin, which is connected to the metal housing of the product. The metal housing in turn has a central grounding point for functional ground. You can ground the module as follows: •...
765-1503/100-000 Connection Connection 9.1 General Information on Installation When laying cables, the local conditions and the applicable regulations are crucial for im- plementation. Be sure to maintain the minimum clearances between the cabling and possible sources of interference (including machines, welding equipment and power lines) to prevent loss and corruption of data.
WAGO recommends using pre-assembled cables. Power supply 2L is required to power actuators. The following figure gives an example of feeding in and passing on the supply voltages: Product manual | Version: 2.0.0...
Page 49
765-1503/100-000 Connection Figure 7: Example of Feeding in and Passing on the Supply Voltages In connection with this figure, note that the cables illustrated for current paths 1L and 2L are realized not as separate cables, but rather as separate wires within one common ca- ble.
Cable cross-section 9.3 Connecting Cables WAGO recommends using 765 Series connecting cables, pluggable connectors and ac- cessories for 756 Series products, which have been tailored specifically to the WAGO I/O System Field. 8 Connection Technology [} 18] The tightening torques given in section apply to the pluggable connectors of the connecting cables.
Page 51
3. Tighten the pluggable connector using the knurled-head screw. Connecting Multiple Products to One ETHERNET Network The fieldbus module of the WAGO I/O System Field has two connections with an inte- grated switch to allow wiring of a line topology.
Connection 765-1503/100-000 Figure 9: Network Topology (Module Appearance May Differ) 9.5 Connect Sensors/Actuators The sensor/actuator cable powers the connected sensors/actuators and transfers the sensor and actuator signals. Note the current load capacity of the supply contacts; see “Rule 3,” section Rule 3: Ports 8 Designing the Power Supply...
Page 53
765-1503/100-000 Connection Ethernet Ethernet PWR OUT PWR IN DO B DO B DO A DO A 3 2L- DO B DO B DO A DO A 3 2L- DO B DO B DO A DO A 3 2L- DO B...
Connection 765-1503/100-000 Table 33: Connecting Digital Outputs Connection Option Description Connection of a digital output to channel A. Required port configuration: pin 4 and pin 2 as a digital input. Connection of two digital outputs to channels A and B. Required port configuration: pin 4 and pin 2 as a digital output.
765-1503/100-000 Commissioning Commissioning Note The figures and descriptions below are an example configuration The figures and descriptions this section contains are based on an example configura- tion. Your configuration, and thus the content shown, may differ from the content illustrated here.
The individual steps are describe in detail below. 10.2.1.1 Selecting the Module Select the module used from the device catalog. Module: 765-1503/100-000 Designation:16 DO FLD EI 24 VDC 2.0 A 10.2.1.2 Selecting a Connection The module offers multiple connections. Select a connection for your application. By se- lecting the connection, you determine the following: •...
765-1503/100-000 Commissioning Scanner Sends IO-Link Parameters to the Module (Only for Modules with IO-Link Master Ports) With “Exclusive Owner without Config” and “Listen Only” connections, the scanner does not transfer any port parameters. For these connection types, the port parameters are set with a different tool.
10.3.1.2 User Interface of the WAGO Webserver I/O Field Figure 11: Dashboard Menu Item, Main Page (Example View) When the user interface of the WAGO I/O Field Webserver opens, the main page of the Dashboard appears first. It shows the following product information: Product manual | Version: 2.0.0...
• A list of the licensed software components the product contains • A link for each licensed software component to the associated license terms 10.3.1.3 Opening the Product Information via WAGO Webserver I/O Field 10.3.1.3.1 Display Port Information For each of the digital inputs/outputs of the module (port X01, port X02, etc.), individual port information can be found on the Information, Status, Configuration and Process data tabs.
Commissioning 765-1503/100-000 Table 36: Tab for port information (digital inputs/outputs X01, X02, etc.) Description Information Displays the current measured values for temperature, voltage and cur- rent, as well as the port state, individually for pin 1, pin 2 and pin 4. If an IO-Link device is connected to the digital input/output, its product data is also shown.
765-1503/100-000 Commissioning • Overvoltage • Undervoltage • Module-internal watchdog timer has elapsed 10.3.1.3.3 Display Port Status Information Figure 13: Port XX Menu Item, Status Tab (Example View) The Status tab shows status information for pins 2 and 4 of the selected port.
765-1503/100-000 Figure 14: Port X0i Menu Item, Process Data Tab (Example View) 10.3.1.4 Parameterizing the Module via the WAGO I/O Field Webserver You can make the following settings on the module with WAGO Webserver I/O Field: 8 Configure Ports [} 63] • 8 Configuring IP Parameters [} 64] •...
765-1503/100-000 Commissioning 10.3.1.4.1 Configure Ports Figure 15: Port XX Menu Item, Configuration Tab Table 37: Port Configuration Settings Name Type Description Port mode (pin 4) Drop-down menu Port operating mode (configuration of pin 4) Digital input signal filter Drop-down menu Filter time for digital input signals on pin 4 (only for (pin 4) “Port mode (pin 4)”...
Commissioning 765-1503/100-000 Table 38: “Port Mode” Drop-Down Menu: Selecting the Operating Mode for Pin 2 and Pin 4 of the Selected IO- Link Port Selection Option Description Digital Output The port is used as a digital output. All elements of the port configuration are ig- nored except for the input and output data length.
765-1503/100-000 Commissioning • If static configuration is used, specify the IP address and subnet mask manually (the gateway IP address is optional). Table 40: Device Configuration Tab – Parameter Overview Parameter Settings/Action Device IP address IP address for the ETHERNET configuration with static IP address configuration...
4. Click the [Apply] button. ð Your changes take effect. 10.3.1.4.4 Update Firmware With the Firmware upgrade tab, WAGO Webserver I/O Field provides the option to up- date the product firmware. Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Page 67
To update the firmware, you need a firmware container file: FWUPDATE.ZIP. You can get it from the Downloads section of the WAGO website: ü http://www.wago.com. Proceed as follows to update the firmware: 1. In the left-hand column of the WAGO I/O Field Webserver, click the Settings menu item. ð The Device configuration tab appears.
Commissioning 765-1503/100-000 The firmware update procedure is as follows: 1. The firmware from the FWUPDATE.ZIP firmware container file is stored in the mod- ule’s flash memory. 2. An internal reset is triggered. 3. Then the device maintenance firmware starts; this edits the firmware container file and installs the new firmware, including the module’s configuration files.
765-1503/100-000 Commissioning 1. In the left-hand column of the WAGO I/O Field Webserver, click the Settings menu item. ð The Device configuration tab appears. 2. Select the Factory reset tab. 3. Use the radio buttons to select the settings that you want to reset to their factory set- ting values.
® To enable the Bluetooth interface, you must have the WAGO I/O Field app installed on the smartphone or tablet. Proceed as follows: ® • A DM code appears in the “Information” section of the Bluetooth tab.
765-1503/100-000 Commissioning ð The light sensor registers this sequence. If the sequence is recognized as correct, the ® ® Bluetooth interface is enabled, and the product attempts to establish a Bluetooth connection to the smartphone or tablet. ® Starting a Bluetooth Firmware Update ®...
Page 72
From the Webserver main menu (left), select the Sign out menu item. ð You can now no longer work in the WAGO I/O Field Webserver with the rights you had been using till this point. The username used to log on is no longer shown in the upper left-hand corner.
Page 73
765-1503/100-000 Commissioning The Administration tab provides role-based user administration. It allows you to create and delete users and assign them roles, which their rights depend on. Users can be di- vided into three roles: • Maintenance • Operator • Administrator Creating a New User When “User administration”...
Commissioning 765-1503/100-000 Figure 23: User Administration Menu Item (Example View) ð The new user is created and assigned the selected role. Removing Users To remove an existing user from the product’s user administration, proceed as follows: • Click the red square with the white “x” to the right of the user you want to remove.
765-1503/100-000 Commissioning Figure 24: DIO Forcing Menu Item, “DIO Forcing” Screen (Example View) You have three options for each pin that supports the forcing function: Table 44: Input Options for Forcing for Each Pin of a Port Option “Force” Checkbox “Set/Clr” Checkbox Forcing –...
As long as one user is accessing the forcing functionality through a forcing medium, e.g., the WAGO I/O Field Webserver, it is locked for all other users of the module. They cannot access the forcing functionality until the user that is active now terminates his or her ac- cess.
765-1503/100-000 Commissioning Figure 25: OPC UA: Device Information Model 10.3.3.1 Parameterizing the Product via OPC UA 10.3.3.1.1 Identifying Devices The device provides nodes for device identification. For example, the OPC UA client can read out the version of the device firmware used in the SoftwareRevision node. The path to this node is: Root >...
Commissioning 765-1503/100-000 10.3.3.1.2 Setting Device Parameters The OPC UA server provides nodes with configuration parameters for the device. For ex- ample, the OPC UA client can read out the upper limiting value for temperature in the OverTemperature node. The path to this node is: Root >...
765-1503/100-000 Commissioning Table 47: Port-Specific Configuration Parameters Node Name Node Class Access Default Description OverCurrentPin1 Variable Read Warning level for current upper limit on pin 1; unit: 1 mA 0: monitoring not enabled OverCurrentPin2 Variable Read Warning level for current upper limit on pin 2;...
Commissioning 765-1503/100-000 The path to this node is: Root > Object > DeviceSet > [device name] > DigitalConnector > Di- agnostics > Current The following table lists device-specific (calculated) measured current values. Table 49: Device-Specific (Calculated) Measured Current Values Node Name...
765-1503/100-000 Commissioning Table 52: Port-Specific Diagnostics Node Name Node Class Access Description DiagnosticsPin1, Di- Variable Read Diagnostics on pin 1, pin 2 or pin 4; the nu- agnosticsPin2, Diag- merical value contains bit-coded informa- nosticsPin4 tion: Bit 0: short circuit Bit 1: overload protection...
Commissioning 765-1503/100-000 Measurement Node Name Node Class Access Description MaxTemperature- Variable Read Maximum tempera- Pin2 ture on pin 2 since the value was reset; unit: °C MaxTemperature- Variable Read Maximum tempera- Pin4 ture on pin 4 since the value was reset; unit: °C...
765-1503/100-000 Commissioning Table 54: NTP Client Configuration Node Name Node Access Default Description Class NtpClientServerIpAd- Variable Read/ IP address of the NTP server dress write The NTP client uses the IP address setting to retrieve the time from an NTP server.
Commissioning 765-1503/100-000 While the Force function is enabled, the watchdog timer needs to be triggered regularly. Triggering occurs each time an input simulation and output method is called. The watch- dog timer is also triggered when the “AssignedForceID” node is read. This means that regular reading of the “AssignedForceID”...
Page 85
765-1503/100-000 Commissioning Figure 26: Add Server Dialog – Discovery Tab (Default) Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Page 86
Commissioning 765-1503/100-000 Figure 27: Add Server Dialog – Advanced Tab 4. In the Configuration Name field, enter a name for your configuration, e.g. “Test.” 5. Select the Advanced tab. 6. In the Server Information section of the Advanced tab, enter the following informa- tion in the Endpoint URL field: opc.tcp://<IP address>:4840.
Page 87
765-1503/100-000 Commissioning 9. Click OK. ð In the project window, UaExpert enters the server under Project > Servers e.g., “Test.” 10. Open the context menu of the server (“Test”) and select Connect. ð The connection is established. 10.3.3.1.10.2 Setting the Module Time via OPC UA Requirements •...
Page 88
Commissioning 765-1503/100-000 Figure 28: NtpClientUpdateConfiguration Node 2. In the context menu, select Call. Figure 29: NtpClientUpdateConfiguration Node – Context Menu ð The Call NtpClientUpdateConfiguration on NtpClient dialog appears. Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Page 89
765-1503/100-000 Commissioning Figure 30: NTP Client Configuration Dialog 3. In the Input Arguments section, enter the value 3224725356 for the IP address of the NTP server in the ServerIpAddress field. 4. In the Input Arguments section, enter the number 3224725352 for the IP address of the alternate NTP in the ServerIpAddressFallback field.
Page 90
Commissioning 765-1503/100-000 Figure 31: NTP Client Configuration Dialog (Succeeded) 10.3.3.1.10.3 Enabling Forcing Requirements • You must have an OPC UA client. • You must know the username and password, and this user must have permission to execute methods. • You must have already established a connection to the I/O module.
Page 91
765-1503/100-000 Commissioning Figure 32: GetForcingID Method 3. Click [Call]. ð If the method call was successful, then the Force ID is displayed, and “0” appears under Status. The FLD LED on the I/O module flashes at a rate of 1 Hz. Figure 33: GetForcingID Method: Successful ð...
Page 92
Commissioning 765-1503/100-000 Figure 34: GetForcingID Method: Unsuccessful 4. In the OPC UA client, drag the “AssignedForceID” node into the Data Access View window so that the AssignedForceID is read regularly ð Regular reading of the AssignedForceID triggers the watchdog timer and keeps the Force function enabled.
765-1503/100-000 Commissioning Figure 35: OutputPin4 Method 4. Click [Call]. ð If the method call was successful, then the output data on the module is forced. ð If the method call was unsuccessful, then “−1” appears under Status. Description of the Input Arguments Table 55: Input Arguments of the OutputPin Method...
Commissioning 765-1503/100-000 Input Arguments Description Example 1 (Force Mask has a value of 4): A value of 0 sets the output value of port X03 to 0. A value of 4 sets the output value of port X03 to 1.
765-1503/100-000 Commissioning Figure 36: DisableForcing Method ð If the method call was unsuccessful, then “−1” appears under Status. Description of the Input Arguments Table 57: Input Arguments of the DisableForcing Method Input Arguments Description Force ID Here the OPC UA client must use the Force ID that the OPC UA client had received after the GetForcingID method was called.
Green Normal operating state Green Flashing (1 Hz) Force mode is active Green Flashing (4 Hz) WAGO IO-Link Configurator is connected to the module Yellow Configuration error Non-operational; no voltage Application Status The APL LED indicates the status of the application. Product manual | Version: 2.0.0...
765-1503/100-000 Diagnostics Table 62: APL LED Color State Description Duo LED, red/green/yellow (yellow = simultaneously red and green) LED without function EtherNet/IP Adapter Status The MS and NS LEDs indicate the status of the EtherNet/IP module. The LNK and ACT LEDs indicate the Ethernet status.
Diagnostics 765-1503/100-000 Color State Description Green/red/off Rapid flashing: Self test: The module runs through a self green/red/off test after it is switched on. See the descrip- tion of the “MS” LED and the description of the “Self test” status. Red/green/off...
765-1503/100-000 Diagnostics ® Bluetooth Status ® ® The Bluetooth LED is integrated into the Bluetooth antenna and indicates the connec- tion status. ® Table 67: LED States Color State Description Duo LED, blue/red ® Blue Bluetooth connection established ® Bluetooth inactive Port Status LEDs 0 (port X01), 2 (port X02), 4 (port X03), ..., 14 (port X08) display the status of digital...
Page 100
Diagnostics 765-1503/100-000 CIP Status Description 3 (0x03) Invalid parameter value See CIP status 32 (0x20). 4 (0x04) Path segment error A path segment error has occurred. The path information could not be evaluated. 5 (0x05) Path destination unknown The addressed CIP class or CIP instance is unknown.
Page 101
765-1503/100-000 Diagnostics CIP Status Description 24 (0x18) No saved attribute data The attribute data for this object was not saved before the service was requested. 25 (0x19) Save attempt failed The object’s attribute data could not be saved because an error occurred during a save attempt.
Page 102
Diagnostics 765-1503/100-000 CIP Status Description 42 (0x2A) General error in the “Only-Group-2 Server” This DeviceNet-specific error cannot occur in Ethernet/IP. 43 (0x2B) Reserved – 207 (0xCF) Reserved for future extensions of the CIP standard. 208 (0xD0) Reserved for object classes and service errors –...
765-1503/100-000 Service Service 12.1 Resetting to Factory Settings The device can be reset to the factory settings. Use the WAGO I/O Field Webserver for this purpose. 8 Resetsetting the Module to the Factory You can find information on the procedure in Settings [} 68].
Decommissioning 765-1503/100-000 Decommissioning 13.1 Disposal and Recycling Table 70: WEEE Mark Logo Description Electrical and electronic equipment may not be disposed of with household waste. This also applies to products without this mark. Electrical and electronic equipment contain materials and substances that can be harmful to the environment and health.
EU Declaration of Conformity Hereby, WAGO GmbH & Co. KG declares that the radio equipment type 765-1503/100-000 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: ü www.wago.com /765-1503/100-000.
GmbH & Co. KG may void the FCC authorization to operate this equipment. 14.2 Operational Description Product Description The product 765-1503/100-000 is used to output digital field signals, e.g., to actuators, which have been received by a higher-level controller. Description of operation (FCC) The product, a fieldbus module in the IP67 housing, serves the acquisition and output of data via sensors and actuators for the industrial control technology.
765-1503/100-000 Appendix Product Designs SlimLine (W × H × D) 35 × 30 × 210 mm WideLine (W × H × D) 60 × 30 × 210 mm Temperature Ranges Table 72: Temperature Ranges Ambient temperature (operation) –25 °C ... +70 °C Ambient temperature (storage) –40 °C ... +80 °C...
Appendix 765-1503/100-000 14.3 Protected Rights ® ® • Adobe and Acrobat are registered trademarks of Adobe Systems Inc. • Android is a trademark of Google LLC. • Apple, the Apple logo, iPhone, iPad and iPod touch are registered trademarks of Apple Inc.
Page 109
Overview of Parameterization Tools .................. Table 25 Parameterization Overview....................Table 26 Function Overview for the WAGO I/O Field Webserver for Digital Input/Output Modules . Table 27 Upper Limits for Current on the Individual Pins of the Connections ........Table 28 Module 765-1503/100-000 –...
Page 110
List of Tables 765-1503/100-000 Table 37 Port Configuration Settings ....................Table 38 “Port Mode” Drop-Down Menu: Selecting the Operating Mode for Pin 2 and Pin 4 of the Selected IO-Link Port......................Table 39 Configuration Control Drop-Down Menu ................ Table 40 Device Configuration Tab –...
Page 111
Figure 1 View ..........................Figure 2 Circuit Diagram for Each Port ..................Figure 3 Derating, 765-1503/100-000 ..................Figure 4 Derating of a Contact (Pin) of L-Coded Connections X31 and X32 (For Core Cross- Section = 0.25 mm /AWG 14) ..................Figure 5 Derating of a Contact (Pin) of the A-Coded Connections Port X01, X02, ...
Page 112
List of Figures 765-1503/100-000 Figure 36 DisableForcing Method ....................Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Page 113
765-1503/100-000 List of Figures Product manual | Version: 2.0.0 16DO FLD EI DC 24V 2.0A...
Page 114
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Copyright – WAGO GmbH & Co. KG – All rights reserved. The content and structure of the WAGO websites, catalogs, videos and other WAGO media are subject to copyright. Distri- bution or modification of the contents of these pages and videos is prohibited. Furthermore, the content may neither be copied nor made available to third parties for commercial pur-...