Kohler Decision-Maker 1 Manual page 121

Refer
Status Event to
or Fault
Menu
Starter 'B' 10
Starting Aid
(see Time Delay
Starting Aid)
Sync TImeout 10, 16
System Ready 10
Time Delay Engine 8, 10
Cooldown (TDEC)
Time Delay Engine 8, 10
Start (TDES)
Time Delay Starting 8, 10
Aid
Underfrequency 7, 10
Undervoltage 7, 8,
Shutdown 10
Weak Battery 10
* DD/MTU engine with MDEC/ADEC
[ NFPA applications
User-Defined Settings
Calibration
Voltage Adjustment
Underfrequency Unload
Frequency Setpoint
Underfrequency Unload
Slope
Reactive Droop
Regulator gain or stability
Volts match window
Volts match gain
Volts match reset
Synch frequency window
Frequency match gain
PGEN ID
No. of PGEN nodes
Phase match window
Phase match gain
Phase match reset
Dwell time
First on close time delay
Fail to switch time delay
Volt/frequency ok timer
TP-6356 4/12
Relay
Driver
Output
(RDO)
Digital Display
STARTER 'B'
FAILURE
SYNC
TIMEOUT
RDO-1
(lead 60)
DELAY ENG RDO-4
COOLDOWN (lead 70C)
DELAY ENG RDO-15
START
RDO-16
UNDER
FREQUENCY
UNDER
VOLTAGE
WEAK
BATTERY
Refer
to
Menu
Digital Display
11 VOLT ADJ
11 FREQUENCY SETPOINT
11 SLOPE
11 VOLTAGE DROOP
11 REGULATOR GAIN ADJ
16 VOLTS MATCH WINDOW
16 VOLTS MATCH GAIN
16 VOLTS MATCH RESET
16 SYNCH FREQ WINDOW
16 FREQ MATCH GAIN
16 GENERATOR ID
16 NBR OF NODES ON BUS
16 PHASE MATCH WINDOW
16 PHASE MATCH GAIN
16 PHASE MATCH RESET
16 DWELL TIME
16 FIRST ON CLOSE TD
16 FAIL TO SYNCH TD
16 VOLT_FREQ OK TIMER
Default
Selection
Range Setting
60 sec.
delay
00:00--10:00 5:00
min:sec
00:00--5:00 00:00
min:sec
0--10 sec. 0:00
80%--100% 97% FAA
80%
70%--100% 70%
30-sec time
delay
Fixed 60% of
nominal
] 3x (times) energize time shown in Menu 17
Range Setting
±20% of system voltage
40 to 70 Hz
0--10% of rated voltage
volts per cycle
0--10% of system voltage
1--10000
+/-- 1--10% V
0--99.99
0--50 sec.
+/-- 0.1--5 Hz
0.01--99.99
0--8 (0 by reset)
0--8 (0 by reset)
+/-- 1.0--20.0 degrees
0--99.99
0--50 sec.
0.1--30 sec.
0.5--10 sec.
10--600 sec.
0--10 sec.
Section 7 Decision-Makerr 6000 Controller
Inhibit
Time Time
Delay User-Defined
Delay
(sec.) (sec.)
Not adjustable
0--600
Not adjustable
10
5--30
2
User-Defined
Default Selection
System voltage
1 Hz below system freq.
(ECM)
2 Hz below system freq.
(non-ECM)
3.1% of system
voltage
4% of system voltage
100
+/-- 1.0% V
1.00
1.0 sec.
+/-- 2.0 Hz
1.00
0
0
+/-- 5.0 degrees
1.0
1.0 sec.
0.3 sec.
0.5 sec.
300 sec.
0.5 sec.
Settings
—
Settings
121