Routing - Korg Triton Studio Parameter Manual

2. Routing

You can use up to two channels (MFX1 and 2) for the Master
Effects in any mode other than in Sampling mode. (You can-
not use the Master Effects in Sampling mode.) If you are not
using any Insert Effects in any mode, the Master Effects send
levels are determined by the "Send1 (MFX1)" and "Send2
(MFX2)" parameters specified independently for the oscilla-
tors (Program), timbres (Combination), tracks (Sequencer
and Song Play), and audio inputs (Global). For example, you
can apply substantial reverberation to a piano sound
assigned to the timbre and tracks, a small amount of rever-
beration to the strings sound, and no reverberation to the
bass sound. If you are using the Insert Effects, set the
"Send1" and "Send2" parameters for the post-IFX signals.
2–1. Program mode
Use the "Send1 (to MFX1)" and "Send2 (to MFX2)" parame-
ters of the P8: "Routing" page, or the "Send1" and "Send2"
parameters of the P8: "Insert FX" page for the post-IFX1–5
signals, to set the Master Effect send level.
If you have set "BUS Select" to L/R or Off, "Send1 (MFX1)"
and "Send2 (MFX2)" of the "Routing" page are effective.
These parameters can be set for oscillators 1 and 2 individu-
ally.
If you have set "BUS Select" to IFX1–5, "Send1" and
"Send2" of the "Insert FX" page for the post-IFX1–5 signals
are effective. If you are using the Insert Effects in chain
(series), the "Send1" and "Send2" parameters for the post-
IFX (last IFX) are effective.
If you have set "BUS Select" to 1, 2, 3, 4, 1/2, or 3/4, the oscil-
lator signals are output directly to AUDIO OUTPUT (INDI-
VIDUAL) 1, 2, 3, or 4 ( "Individual Outputs"). In this case
the Send 1 and Send 2 settings are ignored, and the Master
Effects will not be applied. ( p.185)
Send1 responds to CC#93 and Send2 responds to
CC#91 on MIDI Global channel "MIDI Channel" (Glo-
bal P1: 1–1a). At this time, the actual send level uses the
value of the Send 1 and 2 settings for Oscillators 1 and
2, multiplied by the Send 1 and 2 values received via
MIDI.
If you have selected "Drums" for "Oscillator Mode" (Pro-
gram P1: 1–1a) of a Program, the "USE DKit Setting" box
(Program P8: 8–1b) becomes available.
If you check this box, Send1 and Send2 levels for each key
of the selected DrumKit become effective. If "BUS Select"
(Global P5: 5–2b) is set to L/R or Off for a drum instrument
key, "Send1 (to MFX1)" and "Send2(toMFX2)" (Global P5:
5–2b) become effective. If "BUS Select" is set to IFX1–5,
"Send1" and "Send2" (Program P8: 8–2a) become effective.
If this is unchecked, the routing will be the same as when
"Oscillator Mode" is Single or Double, and the "Send1
(MFX1)" and "Send2 (MFX2)" (Program P8: 8–1d) settings
or the post-IFX1–5 "Send1" and "Send2" settings of the P8:
Insert FX page IFX1–5 (Program P8: 8–2a) will apply to all
drum instruments.
2–2. Combination, Sequencer, and Song Play
modes
Use "Send1 (MFX1)" and "Send2 (MFX2)" (P8: "Routing"
page) for timbres (Combination) and tracks (Sequencer,
Song Play) to set the Send1 and 2 levels for each timbre and
track. As with Program mode, if "BUS Select" is set to L/R
or Off, "Send1 (MFX1)" and "Send2 (MFX2)" become effec-
tive. At this time, the actual levels use these Send1 and 2
level values, multiplied by the send level values of oscilla-
tors 1 and 2 ("Oscillator Mode" is set to "Double") of the
Program P8: "Routing" page.
– Send level –
For example, if a Program's "OSC1 Send1" is set to 127,
"Send2" set to 064, "OSC2 Send1" set to 064, "Send2" set to
127, a Combination's "Send1" set to 064, and "Send2" set to
127, the actual send levels of the combination are calculated
as follows:
OSC1 Send1=127 (100%)*064(50%)=064(50%)
OSC1 Send2=064 (50%)*127(100%)=064(50%)
OSC2 Send1=064 (50%)*064(50%)=032(25%)
OSC2 Send2=127 (100%)*127(100%)=127(100%)
If IFX1–5 is selected for "BUS Select", use the "Send1" and
"Send2" parameters for the post-IFX signals.
If 1, 2, 3, 4, 1/2, or 3/4 is selected instead, these Send1 and 2
settings are ignored and the Master Effect is not applied.
Send1 responds to CC#93, and Send2 responds to
CC#91. If "Send1 (MFX1)" and Send2 (MFX2)" for each
timbre/track are effective, the parameter will be con-
trolled on the MIDI channels set for the corresponding
timbres and tracks. If the "Send1" and "Send2" param-
eters for the post-IFX1–5 signals are effective, they can
be controlled on the MIDI channels assigned to IFX1–5.
The following examples are in Combination mode. In the
upper figure, "BUS Select" is set so that Timbre 1 is routed
to IFX1, Timbre 2 to IFX2, Timbre 3 to IFX3, Timbre 4 to
IFX4, Timbres 5 and 6 to IFX5, and Timbres 7 and 8 to L/R.
In this case, use "Send1" and "Send2" for the post-IFX1(001:
St. Amp Simulation) signal to set the send level of the Tim-
bre 1 routed to the Master Effect. (In this example they are
set to 032 and 127.) In the same way, use "Send1" and
"Send2" for the post-IFX2, 3, and 4 signals to set the send
levels of Timbres 2, 3, and 4, and use the "Send1" and
"Send2" parameters for the post-IFX5 signal to set the send
levels of Timbres 5 and 6. For Timbres 7 and 8, the settings of
"Send1 (MFX1)" and "Send2 (MFX2)" will be effective. (At
183