7-4: Scan Zone; Settings For Arpeggiator A; Settings For Arpeggiator B - Korg Triton Studio Parameter Manual

M 7–1: Page Menu Command
7–1A: Copy Arpeggiator
This command can copy arpeggiator settings from another
location to the current Combi.
1 Select "Copy Arpeggiator" to access the dialog box.
2 In "From" select the source (mode, bank, number) of the
arpeggiator you wish to copy.
If you are copying from Combination, Song, or Song Play
mode, select either A or B to if you wish to copy settings
from only one arpeggiator, or select A&B if you wish to
copy the settings of both arpeggiators.
3 If you are copying from a Program, or are copying either
A or B from Combination, Song, or Song Play mode,
select either A or B as the "To" copy destination.
4 To execute the Copy Arpeggiator command, press the
OK button. To cancel, press the Cancel button.
7–2: Arpegg. A
(Arpeggiator A)
7–3: Arpegg. B
(Arpeggiator B)
The Arpeggiator A pages allow you to adjust the settings for
arpeggiator A. The Arpeggiator B pages allow you to adjust
the settings for arpeggiator B.
You can also use the "Copy Arpeggiator" page menu
command to copy arpeggiator settings from Program
mode or another mode.
1–1a
7–2a
7–2(3)a: Arpeggiator-A(B) Setup
Pattern* [P00...P04, U000(I-A/B)...U506(User)]
Octave*
Resolution*
Gate
Velocity
Swing
Sort*
Latch*
0–1A
0–1B
7–1A
7–1
7–1a
[1, 2, 3, 4]
[ , , , , , ]
[000...100%, Step]
[001...127, Key, Step]
[–100...+100%]
[Off, On]
[Off, On]
Key Sync.*
Keyboard*
These parameters are the arpeggiator settings for the combi-
nation. ( "Program P7: Edit-Arpeggiator")
* These parameters can also be set from "0–3(4): Arpegg.
A(B)".
7–4: Scan Zone
(Scan Zone A/B)
These settings specify the note and velocity ranges that will
operate arpeggiators A and B.
1–1a
7–4a
7–4b
7–4a: Zone Map
This shows the Scan Zone for each arpeggiator, A and B.
Key zone of arpeggiator B
Key zone of arpeggiator A
C–1
7–4b: Scan Zone A/B
A:
Top Key
Bottom Key
Specifies the range of notes (keys) that will operate arpeg-
giator A. "Top Key" specifies the upper limit, and "Bottom
Key" specifies the lower limit.
Top Velocity
Bottom Velocity
Specifies the range of velocities that will operate arpeggiator
A. "Top Velocity" specifies the upper limit, and "Bottom
Velocity" specifies the lower limit.
B:
Top Key
Bottom Key
Top Velocity
Bottom Velocity
Specifies the range of notes (keys) and velocities that will
operate arpeggiator B ( A:).
The values of these parameters can also be entered by
holding down the [ENTER] key and playing a note on
the keyboard.
[Off, On]
[Off, On]
7–1
7–1a
Velocity zone of
arpeggiator A
Velocity zone of
arpeggiator B
G9
[C–1...G9]
[C–1...G9]
[001...127]
[001...127]
[C–1...G9]
[C–1...G9]
[001...127]
[001...127]
45