Option Boards/Memory/Calendar Battery; Please Note When Installing An Option Board/Memory; Cautions When Installing The Calendar Battery - Korg Triton Studio Parameter Manual

Option boards/Memory/Calen-
dar battery
Please read this before you begin installation
Safety precautions
Warnings
• Before installing an option, be sure to disconnect the
power supply cable and the connecting cables to any
peripheral devices. Failure to do so could cause electrical
shock or may damage the device.
• When installing, repairing, or replacing an option, you
must perform only those actions that the owner's
manual directs, and no other.
• Do not apply excessive force to the electronic
components or connectors on the circuit board(s) of an
option, or attempt to disassemble them.
This could cause electric shock, fire, or malfunction.
Cautions
• Before touching the option, touch a metal component of
the device into which it will be installed, to discharge
any static electricity that may be present in your body.
Static electricity may damage the electronic components.
• Be careful of any sharp edges or pointed metal parts on
the option or the device into which the option is being
installed.
Sharp edges or points may cause injury.
• Danger of explosion if battery is incorrectly replaced.
Replace only the same or equivalent type.
• When handling an option, never touch parts that are not
related to the installation.
Doing so may cause electrocution or malfunctions.
• When handling an option, be careful not to touch the
leads on the back side of the circuit board (the side
opposite that on which the components are mounted).
The sharp points may cause injury.
• Do not allow the option or other device being installed
to become wet, and do not allow objects to be placed on
top of it.
Doing so could cause malfunction.
• When installing an option, be careful that screws or
other parts do not fall into the device into which it is
being installed.
Doing so could cause malfunction.
Korg Inc. takes no responsibility for any malfunctions or
damage that may occur from improper use or modifica-
tion of this product. Nor will Korg Inc. be responsible for
any damages resulting from the loss or destruction of
data.
286
Please note when installing an option
board/memory
• So that static electricity in your body does not damage
the electronic components, touch the ground wire of a
grounded device or an unpainted metallic component
to discharge any static electricity in your body before
installing an option board or memory. Internal compo-
nents of the TRITON STUDIO and of the option/
memory boards may be damaged by static electricity.
• Follow the installation procedure, and be sure that
each part is installed correctly and in the correct orien-
tation.
• Please use care in handling option boards/memory.
Dropping them or applying pressure to them may
damage the components.
• Avoid touching exposed metal edges of the circuit
board, or portions that need not be handled during
installation.
• Be careful not to lose the screws (and washers) that
you remove.
• Do not use screws other than those that are installed in
the option board/memory and the TRITON STUDIO.
Using screws of a different shape or length may dam-
age the unit or cause it to malfunction.
• Be sure to firmly tighten the screws used for attach-
ment.
• Be sure that the option board/memory is inserted cor-
rectly into the connector or slot. After installation, be
sure to check that the board is installed correctly. If the
board is not inserted all the way, faulty contact or
power supply shorts can occur, making the unit mal-
function.
• Be careful not to drop parts or the option board/mem-
ory into the inside of the instrument.
If you are unable to retrieve a screw or part that was
dropped inside the instrument, please contact your
local Korg distributor.
Cautions when installing the calendar
battery
• So that static electricity in your body does not damage
the electronic components, touch the ground wire of a
grounded device or an unpainted metallic component
to discharge any static electricity in your body before
installing an option board or memory. Internal compo-
nents of the TRITON STUDIO and of the option/
memory boards may be damaged by static electricity.
• Follow the installation instructions, being careful not
to reverse the polarity of the battery.
• Avoid touching exposed metal edges of the circuit
board, or portions that need not be handled during
installation.
• All screws (and washers) that are removed will be
used, so be careful not to misplace them.
• Do not use screws other than those that are installed in
the TRITON STUDIO. Using screws of a different
shape or length may damage the unit or cause it to
malfunction.
• Be sure to firmly tighten the screws used for attach-
ment.
• When installing the battery, do not use excessive force.
Pressing the battery too hard or using excessive force
may cause malfunctions or damage.
• Make sure that the battery is completely inserted into
the battery holder. After installation, check to make
sure that the battery is firmly in place.