Korg Triton Studio Parameter Manual page 38

7–1b: Arpeggiator Setup
Refer to BG p.130.
Pattern* [P00...P04, U000(I-A/B)...U506(User)]
Selects the arpeggio pattern.
P00...P04 Preset arpeggio patterns
U000(I-A/B)...U199(I-A/B) Preloaded arpeggio patterns
U200(E-A)...U215(E-A)
U216(E-B)...U231(E-B)
U232(E-C)...U247(E-C)
EXB-PCM series
U248(E-D)...U263(E-D)
(user arpeggio patterns)
U264(E-E)...U279(E-E)
U280(E-F)...U295(E-F)
U296(E-G)...U311(E-G)
U312(User)...U506(User) User arpeggio patterns
(some preloaded arpeggio patterns)
U000 (I–A/B)–U506 (User) are rewritable. Use Global
P6 to create arpeggio patterns.
Arpeggio patterns U000 (I-A/B)–U506 (User) can be
selected using the numeric keys [0]–[9] and the
[ENTER] key.
Octave*
Specifies the number of octaves in which the arpeggio will
be played.
If a user arpeggio pattern is selected, the range of the
arpeggio will depend on the "Octave Motion" (Global
P6: 6–1b) setting.
Resolution*
Specifies the timing resolution of the arpeggio. The notes of
the arpeggio will be played at the interval you specify:
, , , , or . The speed of the arpeggio pattern is
determined by the "Arpeggiator Tempo " and the "Resolu-
tion."
Gate
Specifies the length (gate time) of each note in the arpeggio.
000–100(%): Each note will be played with the specified gate
time.
Step: This is available when an user arpeggio pattern U000
(I-A/B)–U506 (User) is selected for "Pattern." When this is
selected, the gate time specified for each step will be used.
The gate time can also be controlled by the ARPEGGIATOR
[GATE] knob. Rotating the knob toward the left will shorten
the gate time, and rotating it toward the right will lengthen
the gate time. When the knob is at the 12 o'clock position,
the gate time will be as specified here.
Velocity
Specifies the velocity of the notes in the arpeggio.
001–127: Each note will sound with the specified velocity
value.
Key: Each note will sound with the velocity value at which
it was actually played.
Step: This is available when an user arpeggio pattern U000
(I-A/B)–U506 (User) is selected for "Pattern." When this is
selected, the velocity specified for each step will be used.
The velocity can also be controlled by the ARPEGGIATOR
[VELOCITY] knob. Rotating the knob toward the left will
decrease the velocity, and rotating it toward the right will
increase the velocity. When the knob is at the 12 o'clock posi-
tion, the velocity will be as specified here.
[1, 2, 3, 4]
[ , , , , , ]
,
[000...100(%), Step]
[001...127, Key, Step]
Swing
This parameter shifts the timing of the odd-numbered notes
of the arpeggio.
When Resolution =
Step 1
2 3 4 5
–50 –25
Swing
Sort*
This specifies the order in which the notes you press will be
arpeggiated.
On (checked): Notes will be arpeggiated in the order of
their pitch, regardless of the order in which you pressed
them.
Off (unchecked): Notes will be arpeggiated in the order in
which you pressed them.
Latch*
Specifies whether or not the arpeggio will continue playing
after you take your hand off of the keyboard.
On (checked): The arpeggio will continue playing after you
remove your hand from the keyboard.
Off (unchecked): The arpeggio will stop when you remove
your hand from the keyboard.
Key Sync.*
Specifies whether the arpeggio pattern will begin when you
press a key, or whether it will always follow the " (Tempo)"
(0–1a).
On (checked): The arpeggio pattern will start playing from
the beginning when a note-on occurs from a condition
where no keys are pressed. This setting is suitable when you
are playing in realtime and want the arpeggio to play from
the beginning of the measure.
Off (unchecked): The arpeggio pattern will always play
according to the " (Tempo)."
Keyboard*
This specifies whether the notes you play on the keyboard
will be sounded as usual in addition to being sounded as
part of the arpeggio ("keyboard" 0–2a).
On (checked): The notes you play will be sounded on their
own, in addition to being sounded as part of the arpeggio.
For example if you simultaneously press two or more notes,
they will be sounded as usual in addition to being played as
arpeggiated notes.
Off (unchecked): Only the arpeggiated notes will be heard.
*: These parameters can also be set from "P0: Play,
Arpeggio."
M 7–1: Page Menu Command
7–1A: Copy Arpeggiator
This command can be used to copy arpeggio settings from
another location to the current program.
[–100...+100(%)]
6 7 8 9
+25 +50
[Off, On]
[Off, On]
[Off, On]
[Off, On]
0–1A
7–1A
27