Midi Transmission When The Triton Studio's Controllers Are Operated - Korg Triton Studio Parameter Manual

MIDI transmission when the
TRITON STUDIO's controllers are
operated
The following table shows the relation between the MIDI
messages that are transmitted when the TRITON STUDIO's
controllers are operated, and the AMS (alternate modulation
source) or DMS (dynamic modulation source) that corre-
spond to each MIDI message. # indicates a fixed function,
and * indicates an assignable function.
MIDI channel messages
Note-off
Note-on (note number)
Note-on (velocity)
Poly after touch
CC# 0 Bank select (MSB)
1 Modulation 1
2 Modulation 2
3 –
4 Foot controller
5 Portamento time
6 Data entry (MSB)
7 Volume
8 Post insertion effect panpot
9 –
10 Panpot
11 Expression
12 Effect control 1
13 Effect control 2
14...15
16 Ribbon controller
17 Knob modulation 1
18 Controller (CC#18)
19 Knob modulation 2
20 Knob modulation 3
21 Knob modulation 4
22...31 –
32 Bank select (LSB)
33...37 –
38 Data entry (LSB)
39...63 –
64 Damper
65 Portamento On/Off
66 Sostenuto On/Off
67 Soft
68...69 –
70 Sustain level
71 Filter resonance level/High pass
filter cutoff frequency
72 Release time
73 Attack time
74 Low pass filter cutoff frequency
75 Decay time
76 LFO1 speed
77 LFO1 depth (pitch)
78 LFO1 delay
79 Filter EG intensity
80 SW1 modulation On/Off
81 SW2 modulation On/Off
82 Foot switch On/Off
83 Controller (CC#83)
84...90 -
91 Effect depth 1 (send 2 level)
92 Effect depth 2 (insertion effect
1,2,3,4,5 On/Off)
93 Effect depth 3 (send 1 level)
94 Effect depth 4 (master effect 1
On/Off)
95 Effect depth 5 (master effect 2
On/Off)
96 Data increment
97 Data decrement
98 NRPN(LSB)
2: Arpeggiator on/off switch
10: Arpeggiator gate control
11: Arpeggiator velocity control
99 NRPN(MSB) 0
100 RPN(LSB)
0: Bend range
1: Fine tune
2: Coarse tune
101 RPN(MSB) 0
102...127 -
Program change
Channel after touch
Bender change
Universal exclusive
Master volume
Master balance
Master fine tune
Master coarse tune
Joy Stick Ribbon Value Realtime Realtime
Slider Controls Controls
A B
*
# (+Y) *
# (–Y) *
*
*
*
*
*
*
*
*
*
*
*
*
# *
*
# *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
* (Knob2) *
* (Knob4) *
*
* (Knob1) *
*
*
*
*
* (Knob3) *
*
*
*
*
*
*
*
*
*
*
# (X)
*
When one of the TRITON STUDIO's controllers is operated,
the corresponding or the assigned control change will be
transmitted. Pitch Bend messages will be transmitted only
when the joystick is moved in the X (horizontal) direction.
When Knob1...4 or SW1, 2 are selected for Assignable Switch
or Assignable Pedal, the corresponding MIDI control change
message will be transmitted according to the Knob1...4 B-
Assign and SW1/2 Assign settings of each mode.
The following page describes operation in each mode. (Only
control changes are explained here, but the same applies to
pitch bend.)
TRITON STUDIO controller
Gate Velocity SW1,2 ARP On/ Damper
Knob Knob Off
*
* (SW1)
* (SW2)
#
#
#
# # #
Available Available
for AMS for
Assign- Assign-
DMOD
able able
Switch Pedal
* *
* *
*
* * * *
* * * *
* * *
*
*
*
*
*
* *
* *
* * * *
* * * *
* *
* *
* *
* *
# * *
* * *
* * *
* *
* *
* *
* * *
* *
*
*
*
*
* *
* *
*
253