Korg Triton Studio Parameter Manual page 4

2. Combination mode. . . . . . . . . 33
Combination P0: Play ................................... 33
Select and play combinations.
Select a program for each timbre ........... 33
0-1: Prog. Select
Specify pan and level ............................... 35
0-2: Mixer
Select an arpeggio pattern and make
0-3: Arpegg. A
settings for arpeggiator A ....................... 36
0-4: Arpegg. B Select an arpeggio pattern and make
settings for arpeggiator B ........................ 36
0-5: Sampling Perform sampling; make audio input
settings etc. ................................................ 36
Combination P1: Edit-Program/Mixer................ 37
Select the program for each timbre, and specify pan and
level.
Specify program, pan, and level of each
1-1: Program/Mixer
timbre ........................................................ 37
Combination P2: Edit-Trk Param ..................... 38
Set various parameters for each timbre.
2-1: MIDI Channel Specify MIDI channel and status for each
timbre ........................................................ 38
Make settings such as mono/poly and
2-2: OSC
portamento for each timbre .................... 38
Make pitch-related settings such as
2-3: Pitch
transpose and bend range for each timbre
.................................................................... 39
2-4: Other Make delay and scale settings for each
timbre ........................................................ 40
Combination P3: Edit-MIDI Filter ..................... 40
Specify MIDI message reception filtering for each timbre.
Program changes, aftertouch etc. ........... 40
3-1: MIDI 1
Joystick, ribbon controller ....................... 41
3-2: MIDI 2
Realtime control knobs ............................ 41
3-3: MIDI 3
SW1/2, foot controller etc. ...................... 41
3-4: MIDI 4
Combination P4: Edit-Zone/Ctrl ....................... 42
Specify the key range and controllers for each timbre.
4-1: Key Z Specify the key zone sounded by each
timbre ........................................................ 42
4-2: Vel Z Specify the range of velocities sounded by
each timbre ................................................ 42
Displayed if the EXB-MOSS option is
4-3: MOSS Setup
installed; set EXB-MOSS parameters ..... 43
Specify the function of the [SW1] and
4-4: Controller
[SW2] keys, and B-mode functions of the
REALTIME CONTROLS [1]-[4] knobs . 43
Combination P7: Edit-Arp...............................44
Make settings for arpeggiators A and B.
7-1: Setup Assign arpeggiators to each timbre .......44
7-2: Arpegg. A Select an arpeggio pattern and make
settings for arpeggiator A .......................45
7-3: Arpegg. B Select an arpeggio pattern and make
settings for arpeggiator B ........................45
7-4: Scan Zone Specify the ranges of notes and velocities
that will operate the arpeggiator ............45
Combination P8: Edit-Insert FX........................46
Specify the output bus for each timbre, and make insert
effect settings.
8-1: Routing Specify the output bus and master effect
send levels for each timbre ......................46
8-2: Insert FX Select insert effects, turn them on/off, and
make chain settings ..................................47
8-3: IFX 1 Parameter settings for IFX1 .....................47
8-4: IFX 2 Parameter settings for IFX2 .....................47
8-5: IFX 3 Parameter settings for IFX3 .....................47
8-6: IFX 4 Parameter settings for IFX4 .....................47
8-7: IFX 5 Parameter settings for IFX5 .....................47
Combination P9: Edit-Master FX ......................48
Make settings for the master effects and master EQ.
9-1: Master FX Select the master effects, turn them on/
off, and make chain settings ...................48
9-2: MFX 1 Parameter settings for MFX1 ..................48
9-3: MFX 2 Parameter settings for MFX2 ..................48
9-4: Master EQ Parameter settings for master EQ ..........48
About the Jump pages
The LCD screens shown here are the Jump pages for each
mode.
The Jump page is a page menu that lets you access the var-
ious pages within each mode.
Here's how to access the Jump page, and select the desired
page.
• Press the [MENU] key to access the Jump page. In the
LCD screen, press the page that you want to select, or
press the numeric key [0]-[9] corresponding to the
number of the desired page. ( BG p.16)
• Alternatively, you can hold down the [MENU] key and
press the numeric key [0]-[9] corresponding to the
number of the desired page.
v