018: Multitap Cho/Delay (Multitap Chorus/Delay); 019: Ensemble - Korg Triton Studio Parameter Manual

g: High/Low Split Point
This parameter sets the frequency that splits the high and low
range. Only the high range will be sent to the chorus block.
h: Feedback
Sets the feedback amount of the chorus block. Increasing the feed-
back will allow you to use the effect as a flanger.
018: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO phase.
You can create a complex stereo image by setting each block's
delay time, depth, output level, and pan individually. You can
also fix some of the chorus blocks to combine the chorus and
delay effects.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
+
Tap3 Delay
Tap4 Delay
Right
0 [degree]
180 [degree]
90 [degree]
270 [degree]
LFO: Triangle
LFO Frequency [Hz]
a
Sets the LFO speed
Tap1(000) [msec]
Sets the Tap1 (LFO phase=0 degrees) delay time
Depth
Sets the Tap1 chorus depth
b
Level
Sets the Tap1 output level
Pan
Sets the Tap1 stereo image
Tap2(180) [msec]
Sets the Tap2 (LFO phase=180 degrees) delay time
Depth
Sets the Tap2 chorus depth
c
Level
Sets the Tap2 output level
Pan
Sets the Tap2 stereo image
Tap3(090) [msec]
Sets the Tap3 (LFO phase=90 degrees) delay time
Depth
Sets the Tap3 chorus depth
d
Level
Sets the Tap3 output level
Pan
Sets the Tap3 stereo image
Tap4(270) [msec]
Sets the Tap4 (LFO phase=270 degrees) delay time
Depth
Sets the Tap4 chorus depth
e
Level
Sets the Tap4 output level
Pan
Sets the Tap4 stereo image
Tap1 Feedback
Sets the Tap1 feedback amount
Src
f Selects the modulation source of Tap1 feedback amount and effect
balance
Amt
Sets the Tap1 feedback amount and modulation amount
Wet / Dry
Level
Pan
Level
Pan
Level
Pan
Level
Pan
Wet / Dry
0.02...13.00Hz
0...570msec
0...30
0...30
L6...L1, C, R1...R6
0...570msec
0...30
0...30
L6...L1, C, R1...R6
0...570msec
0...30
0...30
L6...L1, C, R1...R6
0...570msec
0...30
0...30
L6...L1, C, R1...R6
–100...+100
Off...Tempo
–100...+100
Wet/Dry
Sets the balance between the effect and dry sounds
g
Amt
Sets the modulation amount of the effect balance

019: Ensemble

This Ensemble effect has three chorus blocks that use LFO to
create subtle shimmering, and gives three dimensional depth
and spread to the sound, because the signal is output from the
left, right, and center.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Ensemble
Right
Shimmer
LFO
Speed
Sets the LFO speed
Src
a
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
Depth
Sets the depth of LFO modulation
Src
b
Selects the modulation source of the LFO modulation depth
Amt
Sets the modulation amount of the LFO modulation depth
Shimmer
c
Sets the amount of shimmering of the LFO waveform
Wet/Dry
Sets the balance between the effect and dry sounds
Src
d
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
c: Shimmer
This parameter sets the amount of shimmering of the LFO wave-
form. Increasing this value adds more shimmering, making the
chorus effect more complex and richer.
Level
Dry, 1:99...99:1, Wet
–100...+100
Wet / Dry
Wet / Dry
1...100
Off...Tempo
–100...+100
0...100
Off...Tempo
–100...+100
0...100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Ensemble LFO
Shimmer
Time
197