Korg Triton Studio Parameter Manual page 285

File/path not found
Meaning: When loading a sample file in Disk mode, the
specified file does not exist. Alternatively, the
specified filename does not exist in the location
you selected in a dialog box for choosing another
directory level or other media.
Meaning: When executing the "Delete" command in the
Disk mode Utility page, the specified file did not
exist.
Meaning: When executing the "Copy" command in the Disk
mode Utility page, and you used a wild card to
specify the copy file name, the specified file was
not found. Alternatively, the length of the copy
source path name exceeded 76 characters.
Meaning: In Disk mode or Song Play mode when you used
the Open button to open a directory, the path
length including the selected directory name
exceeded 76 characters.
Meaning: When executing Insert in the Disk mode Make
Audio CD page, you attempted to use the Insert
All button to add a WAVE file, but no WAVE file
with a sampling frequency of 44.1 kHz or 48 kHz
exists in the selected directory.
Action: Check the file or directory.
Meaning: In Disk mode when loading a .KCD file, a WAVE
file listed in the Audio Track List could not be
found.
Action: The file whose Size is not shown in the Disk mode
Make Audio CD page is the one that could not be
found. Check the file or directory, or delete it from
the Audio Track List.
Front sample data used in rear sample
Meaning: When executing "Link" in the Sampling mode
Sample Edit page, the sample data of the front
sample is also being used by the rear sample, and
therefore cannot be overwritten.
Action: Instead of using "Overwrite," specify a different
sample as the save-destination.
I
Illegal file description
Meaning: The filename that you specified when saving a file
or creating a directory contained invalid charac-
ters.
Action: Change the filename you are specifying. Filena-
mes not permitted by MS-DOS cannot be used as
a filename.
Illegal mLAN message
Meaning: The EXB-mLAN received an invalid message (if
the EXB-mLAN option is installed).
Illegal SMF data
Meaning: You attempted to load a file that was not a Stan-
dard MIDI File.
Illegal SMF division
Meaning: You attempted to load a Standard MIDI File that
was timecode-based.
274
Illegal SMF format
Meaning: You attempted to load a Standard MIDI File of a
Inconvertible file exists
Meaning: A file that cannot be used with ISO9660 format
Action:
Index number over limit
Meaning: When sampling into RAM in Combination, Pro-
Action:
M
Master Track can't be recorded alone
Meaning: When realtime-recording a single track, you
Action:
Can't overwrite
Measure size over limit
Meaning: When loading a Standard MIDI File, the number
Meaning: The attempted edit operation would cause the
Action:
Measure number over limit
Meaning: The attempted edit operation would cause the
Action:
Medium changed
Meaning: When executing the "Copy" command in the Disk
Medium unavailable
Meaning: You selected a medium that does not allow writ-
Medium write protected
Meaning: The floppy disk or other writing-destination
Action:
format other than 0 or 1.
exists on the media.
Media that was formatted or written by a device
other than the TRITON STUDIO may be impossi-
ble for the TRITON STUDIO to convert into
ISO9660 format. To perform the conversion, use
the packet writing software that was used to for-
mat or write the media.
gram, or Sequencer mode, there are too many
indexes to be simultaneously converted into a
multisample.
Either convert the samples into a different pro-
gram or multisample, or use Sampling mode to
delete some of the indexes before you continue
sampling.
attempted to begin recording with the master
track as the current track.
Begin recording with a track 1–16.
of events in a measure exceeded the maximum
(approximately 65,535 events).
maximum number of events in a measure
(approximately 65,535) to be exceeded.
Use event editing etc. to delete unwanted data.
track length to exceed 999 measures.
Delete unnecessary measures.
mode Utility page, the media was exchanged or
ejected, and it was not possible to copy between
separate media on the same drive.
ing.
media is write-protected.
Turn off write protect on the floppy disk or other
media, and execute the command once again.