Table Of Contents - Korg Triton Studio Parameter Manual

Table of Contents

1. Program mode. . . . . . . . . . . . . 1
Program P0: Play ......................................... 1
Select and play programs.
0-1: Perf. Edit
0-2: Arpeggio
0-3: Sampling
Program P1: Edit-Basic .................................. 7
Make basic oscillator settings and scale settings etc.
1-1: Program Basic
1-2: OSC Basic
1-3: Velo. Zone
1-4: Controller
Program P2: Edit-Pitch ................................. 12
Make pitch-related settings for oscillators 1 and 2.
2-1: OSC1 P.Mod
2-2: OSC2 P.Mod
2-3: Pitch EG
Program P3: Edit-Filter ................................. 16
Make filter settings for oscillators 1 and 2.
3-1: Filter1
3-2: Filter1 Mod.
3-3: Filter1 LFO Mod. Filter 1 LFO settings to modulate the filter
3-4: Filter1 EG
3-5: Filter2
iv
Select and play programs; use the
Performance Editor for simple editing ... 1
Arpeggio pattern selection and settings . 3
Perform sampling; make settings for
audio inputs etc. ......................................... 4
Oscillator settings for Single/Double/
Drums, Poly/Mono, scale etc. .................. 7
Specify the multisample for oscillators 1
and 2 ............................................................ 9
Velocity zone settings ............................. 11
[SW1] and [SW2] key functions;
REALTIME CONTROLS [1]-[4] knob B-
mode functions ........................................ 12
Specify oscillator 1 pitch modulation via
key position or controllers ...................... 12
Specify oscillator 2 pitch modulation via
key position or controllers ...................... 14
Pitch EG settings ...................................... 14
Filter 1 (for oscillator 1) type, cutoff
frequency, and resonance settings ........ 16
Keyboard tracking and controller settings
to modulate the filter 1 cutoff frequency
.................................................................... 17
1 cutoff frequency .................................... 18
Filter 1 EG settings ................................... 19
Filter 2 (for oscillator 2) type, cutoff
frequency, and resonance settings ........ 21
3-6: Filter2 Mod. Keyboard tracking and controller settings
to modulate the filter 2 cutoff frequency
.................................................................... 21
3-7: Filter2 LFO Mod. Filter 2 LFO settings to modulate the filter
2 cutoff frequency .................................... 21
Filter 2 EG settings ................................... 21
3-8: Filter2 EG
Program P4: Edit-Amp.................................. 21
Make amp settings for oscillators 1 and 2.
4-1: Amp1 Level/Pan Oscillator 1 volume and pan settings .... 21
4-2: Amp1 Mod. Keyboard tracking and controller settings
to modulate amp 1 ................................... 22
4-3: Amp1 EG Amp 1 EG settings ................................... 23
4-4: Amp2 Level/Pan Oscillator 2 volume and pan settings .... 24
4-5: Amp2 Mod. Keyboard tracking and controller settings
to modulate amp 2 ................................... 24
4-6: Amp2 EG Amp 2 EG settings ................................... 24
Program P5: Edit-Common LFO ....................... 25
Make settings for the general purpose LFOs used to cycli-
cally modulate the pitch, filter, and amp of oscillators 1
and 2.
5-1: OSC1 LFO1 OSC1 LFO1 (for oscillator 1) settings .... 25
OSC1 LFO2 (for oscillator 1) settings .... 26
5-2: OSC1 LFO2
5-3: OSC2 LFO1 OSC2 LFO1 (for oscillator 2) settings .... 26
5-4: OSC2 LFO2 OSC2 LFO2 (for oscillator 2) settings .... 26
Program P7: Edit-Arpeggiator ......................... 26
Make settings for the arpeggiator.
7-1: Arpeg. Setup Select an arpeggio pattern and make
settings ....................................................... 26
7-2: Scan Zone Specify the note and velocity ranges that
will operate the arpeggiator ................... 28
Program P8: Edit-Insert Effect......................... 28
Specify the oscillator output bus, and make insert effect
settings.
Specify the oscillator output bus and set
8-1: Routing
the send levels to the master effects ...... 28
8-2: Insert FX Select insert effects and turn them on/off,
and make chain settings .......................... 29
8-3: IFX 1 Parameter settings for IFX1 .................... 30
8-4: IFX 2 Parameter settings for IFX2 .................... 30
Parameter settings for IFX3 .................... 30
8-5: IFX 3
8-6: IFX 4 Parameter settings for IFX4 .................... 30
8-7: IFX 5 Parameter settings for IFX5 .................... 30
Program P9: Edit-Master Effect ....................... 31
Make master effect and master EQ settings.
9-1: Master FX Select master effects and turn them on/
off, and make chain settings ................... 31
9-2: MFX 1 Parameter settings for MFX1 .................. 32
9-3: MFX 2 Parameter settings for MFX2 .................. 32
Parameter settings for master EQ .......... 32
9-4: Master EQ