Korg Triton Studio Parameter Manual page 175

26) Load .WAV:
The selected WAVE file will be loaded as a sample.
1 To load the data, press the OK button. To cancel without
loading, press the Cancel button.
The sample will be loaded after the last sample that cur-
rently exists in the sample memory (RAM) (Append
load).
You can load multiple files within the directory.
( p.162)
Files with an extension of other than .AIF/.WAV cannot
be recognized as AIFF/WAVE files. In this case, use the
Utility "Rename" (0–3A) to change the last four charac-
ters of the filename to ".AIF"/".WAV"
If the data that is loaded as a sample contains a loop
point, you can set "S.Ofs(Start Offset)" (Program P1: 1–
2a) on the TRITON STUDIO so that the sound will
begin from the loop point.
If data whose sample size is 8 bits or less is loaded, it
will be converted into 16 bit data inside the TRITON
STUDIO. This will mean that the amount of internal
memory consumed will be approximately twice as
large as the file size. The increase in size resulting from
this conversion may mean that it is impossible to save
that data on a media.
Loading AKAI S1000/S3000 format Sample files and
Program files
The TRITON STUDIO can load AKAI S1000/S3000 format
Sample files and Program files ( p.165 "About AKAI Pro-
gram files" for more infomation about compatibility). The
loaded Sample or Program file data can be used as a sample
or multisample respectively. When the loaded data is then
saved to storage media, it will be saved as a Korg format
.KSF file or .KMP file respectively.
AKAI S1000/S3000 format stereo Sample files and Program
files whose names end in "-L" and "-R" can be loaded into
the TRITON STUDIO as stereo samples and multisamples.
When the above files are loaded, "-L" and "-R" will auto-
matically be moved to the end of the sample name or multi-
sample name (15th and 16th character) so that they can
automatically be recognized as stereo samples or multisam-
ples.
27) Load AKAI Sample File:
The selected Sample will be loaded as a sample.
1 To load the data, press the OK button. To cancel without
loading, press the Cancel button.
The sample will be loaded after the last sample that cur-
rently exists in the sample memory (RAM) by having
been sampled or loaded (Append load). If the loaded
data is then saved to storage media, it will be saved as a
Korg format .KSF file. (possible to export as a .AIF, .WAV
format 0–2H "Export Smpl AIF/WAV")
If the data that is loaded as a sample contains a loop
point, you can set "S.Offset" (Program P1: 1–2a) on the
TRITON STUDIO so that the sound will begin from the
loop point.
164
selected icon
Sample files
28) Load AKAI Program File:
The selected Program file will be loaded as a multisample.
When the loaded data is saved to storage media, a Program
file will be saved as a .KMP file, and a Sample file will be
saved as a .KSF file.
1 To load the data, press the OK button. To cancel without
selected icon
If the end (11th and 12th characters) of the sample name
is "-L" and "-R," the "-L" and "-R" will automatically
be moved to the end of the TRITON STUDIO's sample
name (15th and 16th characters).
When you load two files whose sample names are iden-
tical except for ending in "-L" and "-R," and assign
them to a stereo multisample in Sampling mode, they
will be recognized as a stereo sample.
Parameter AKAI S1000/S3000
format
Loop points Multiple settings possible
Loop length Settable with resolution
of less than one sample
You can load multiple files within the directory.
( p.162)
loading, press the Cancel button.
The sample will be loaded after the last multisample or
sample that currently exists in the sample memory
(RAM) (Append load). Only valid Program files or Sam-
ples files will be packed and loaded (Append load).
If the Sample files used by the Program file are not in the
current directory or below it, a dialog box will appear,
allowing you to specify the directory. Use the procedure
"If a file to be loaded cannot be found,..." ( p.157) to
load the required Sample files.
Since sample memory (RAM) overflow checking is per-
formed when loading each sample file, an overflow
may occur during the loading process.
If a loaded multisample is assigned samples whose
sample names end in "-L" and "-R," an "-L" and "-R"
will automatically be added to the end (15th and 16th
characters) of the multisample name.
When you load two multisamples whose multisample
names are identical except for ending in "-L" and "-R,"
they will be recognized in Sampling mode as a stereo
multisample.
TRITON STUDIO format
after loading
Of the multiple loop points,
the settings for the first
HOLD loop are used.
If there is no HOLD loop,
the longest loop will be
used.
Resolution of less than one
sample is ignored
selected icon