Master Programming Level
ANN-LED Options
ANN XXX
1=ENABLED
2=MODULES INSTALLED
3=AUTO-CONFIGURE
ANN-BUS XXX Screen #2
The first screen indicates that the ANN-LED at the selected ANN-BUS address is programmed to annunciate Alarms, Troubles and Supervi-
sories for Zones 000 through 009. The programming can be changed using ANN-LED Address Screen 2.
Pressing 1 while viewing ANN-LED Address Screen #2 will program the annunciator module to annunciate either Point (addressable device
address) information or Zone information. Each press of the 1 key will toggle the display between Point and Zone.
Pressing 2 while viewing ANN-LED Address Screen #2 will program the annunciator module to annunciate only Alarms or Alarms, Trou-
bles and Supervisories (ATS). Each press of the 2 key will toggle the display between Alarms and ATS.
Pressing 1 while viewing ANN-LED Address Screen #3 will select the Point or Zone range to be annunciated (refer to the tables in "ANN-
RLED Zone Option - Alarm Only" on page 91 and "ANN-RLED Point Option - Alarm Only" on page 92). Pressing the 1 key will display
an additional screen where the range can be selected.
•
If Zone has been selected, and Alarms Only are to be annunciated, he new screen will give the options of annunciating Zone 000 - 029
or 030 - 049. Two ANN-LED modules are required to annunciate all zones in this configuration.
•
If Zone has been selected, and Alarms, Troubles and Supervisories are to be annunciated, the new screen will give the options of
annunciating Zone 000 - 009, 010 - 019, 020 - 029, 030 - 039, or 040 - 049. Five ANN-LED modules are required to annunciate all
zones in this configuration.
•
If Points has been selected, and Alarms Only are to be annunciated, the new screen will give the options of annunciating Points 001 -
030 and 031 - 050. Two ANN-LED modules are required to annunciate all points in this configuration.
•
If Point has been selected, and Alarms, Troubles and Supervisories are to be annunciated, the new screens will give the options of
annunciating Points 001 - 010, 011 - 020, 021 - 030, 031 - 040 or 041 - 050. Five ANN-LED modules are required to annunciate all
points in this configuration.
ANN-RLED Zone Option - Alarm Only
If Zone is selected as the module option, and the module is programmed to annunciate alarms only, the first ten LEDs on the ANN-RLED
module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the second module
will display the active/alarm status of each zone in the Zone Range programmed for that particular module. The LED assignments for each
ANN-LED module will be as follows.
ES-50X Series Manual — P/N LS10129-000FL-E:D 4/26/2021
Pressing 2 for Module Options while viewing the ANN XXX Address Screen when the ANN-LED option is
selected, will display the following screens:
YES
ANN-LED - ADDR X-1
ZONES
000-009
ALARM, TRBL, SUPV
ANN-LED Address Screen #1
Alarm Silenced
NAC 1 Fault
Earth Fault
Battery Fault
Zone 000
Zone 001
Active/Alarm
Active/Alarm
Zone 005
Zone 006
Active/Alarm
Active/Alarm
Zone 010
Zone 011
Active/Alarm
Active/Alarm
Zone 015
Zone 016
Active/Alarm
Active/Alarm
Zone 020
Zone 021
Active/Alarm
Active/Alarm
Zone 025
Zone 026
Active/Alarm
Active/Alarm
Not Used
Not Used
Not Used
Not Used
Zone 030
Zone 031
Active/Alarm
Active/Alarm
Zone 035
Zone 036
Active/Alarm
Active/Alarm
Zone 040
Zone 041
Active/Alarm
Active/Alarm
Zone 045
Zone 046
Active/Alarm
Active/Alarm
Not Used
Not Used
Not Used
Not Used
ANN-LED - ADDR X-1
1=POINT/ZONE
2=ALARM/ATS
ANN-LED Address Screen #2
NAC 2 Fault
Charger Fault
Zone 002
Active/Alarm
Zone 007
Active/Alarm
Zone 012
Active/Alarm
Zone 017
Active/Alarm
Zone 022
Active/Alarm
Zone 027
Active/Alarm
Table 3.4 ANN-RLED Module #1
Not Used
Not Used
Zone 032
Active/Alarm
Zone 037
Active/Alarm
Zone 042
Active/Alarm
Zone 047
Active/Alarm
Not Used
Not Used
Table 3.5 ANN-RLED Module #2
ANN-LED - ADDR X-1
1=RANGE
ZONE
ATS
ANN-LED Address Screen #3
Not Used
Not Used
Disabled
Maintenance
Zone 003
Zone 004
Active/Alarm
Active/Alarm
Zone 008
Zone 009
Active/Alarm
Active/Alarm
Zone 013
Zone 014
Active/Alarm
Active/Alarm
Zone 018
Zone 019
Active Alarm
Active/Alarm
Zone 023
Zone 024
Active/Alarm
Active/Alarm
Zone 028
Zone 029
Active/Alarm
Active/Alarm
Not Used
Not Used
Not Used
Not Used
Zone 033
Zone 034
Active/Alarm
Active/Alarm
Zone 038
Zone 039
Active/Alarm
Active/Alarm
Zone 043
Zone 044
Active/Alarm
Active/Alarm
Zone 048
Zone 049
Active Alarm
Active/Alarm
Not Used
Not Used
Not Used
Not Used
Programming
ZN000-009
91