Table of Contents
Advertisement
Programming
Zone Assignment
A maximum of five zones can be programmed to each addressable control module. Pressing 2 while viewing Edit Control Screen #3 dis-
plays the following screen:
Note that Z*** represents the Zone Number(s) corresponding to this device. The factory default for an unprogrammed device is Z000 for
general alarm zone. A flashing cursor will appear on the first 0 to the left. Enter the three digit number corresponding to the zone that is to be
assigned to this device. The cursor moves to the next Z*** designation. Continue entering zone assignments or the remaining zones can be
left blank or programmed as general alarm zones Z000. When all desired changes have been made, press the Enter key to store the zone
assignments. The display will return to the Edit Control Screen #3.
Noun/Adjective
EDIT CONTROL
1=NOUN/ADJECTIVE
2=DESCRIPTION
Edit Control Screen #4
1=STANDARD ADJECTIVE
2=STANDARD NOUN
3=CUSTOM ADJECTIVE
4=CUSTOM NOUN
Noun/Adjective Screen
1=NORTH
2=SOUTH
3=EAST
Adjective Screen #1
1=3RD
2=4TH
3=5TH
Adjective Screen #5
1=STANDARD ADJECTIVE
2=STANDARD NOUN
3=CUSTOM ADJECTIVE
4=CUSTOM NOUN
Noun/Adjective Screen
1=BASEMENT
2=BOILER RM
3=CLASSROOM
Noun Screen #1
1=KITCHEN
2=LOBBY
3=OFFICE
Noun Screen #5
Pressing 3 or 4 while viewing the Noun/Adjective Screen will display screens similar to the previous Adjective and Noun Screens. The new
screens will list Custom Adjectives and Nouns which have been programmed into the control panel using the FS-Tools programming utility.
64
ZONE ASSIGNMENT
Z000 Z
Zone Assignment Screen
The Noun/Adjective selection allows the programmer to enter specific descriptors about the control module
currently being programmed. Pressing 1 while viewing Edit Control Screen #4 will cause the following screen
to be displayed:
1=STANDARD ADJECTIVE
2=STANDARD NOUN
3=CUSTOM ADJECTIVE
4=CUSTOM NOUN
Noun/Adjective Screen
Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note
that the keypad down arrow key must be pressed to see all the Adjective screens. Press the number correspond-
ing to the adjective that is to be used as a descriptor for the location of the control module currently being pro-
grammed.
1=WEST
2=FRONT
3=CENTER
Adjective Screen #2
1=FLOOR 1
2=FLOOR 2
3=FLOOR 3
Adjective Screen #6
Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note
that the keypad down arrow key must be pressed to see all the Noun screens. Press the number corresponding to
the noun that is to be used as a descriptor for the location of the control module currently being programmed.
1=CLOSET
2=CORRIDOR
3=ELECTRIC RM
Noun Screen #2
1=PATIENT
2=RESTROOM
3=ROOM
Noun Screen #6
Z
Z
1=REAR
2=UPPER
3=LOWER
Adjective Screen #3
1=FLOOR 4
2=FLOOR 5
3=ROOM
Adjective Screen #7
1=ELEVATOR
2=ENTRANCE
3=FLOOR
Noun Screen #3
1=STAIRWAY
2=STOREROOM
3=WING
Noun Screen #7
ES-50X Series Manual — P/N LS10129-000FL-E:D 4/26/2021
Master Programming Level
1=MAIN
2=FIRST
3=2ND
Adjective Screen #4
1=GARAGE
2=HALLWAY
3=HVAC RM
Noun Screen #4
1=ZONE
Noun Screen #8
Advertisement
Table of Contents
