Configurations Of The Rotary - Lightware RAP-B511-EU User Manual

   
5. Software Control - Lightware Device Controller
5.4.3. Configurations of the Rotary
Click the rotary icon on the wireframe view to display and modify the related configuration.
The jog dial knob can be configured for volume control (or other controlling purposes). Turning left and right
the rotary triggers the command sending via RS-232 or Ethernet.
Mute and unmute commands are assigned to the knob press, level 0-16 commands belong to the volume
setting on a 16-level scale.
Follow the instructions to set the rotary:
Step 1. Choose an interface for the (volume) command sending (via RS-232 port or via Ethernet port). When
the Ethernet is selected, IP address and port number are also required.
Step 2. Choose a volume control schema: Custom or Lightware.
a) Custom schema makes it possible to send serial or Ethernet messages to the third-party (or Lightware)
device depending on the rotary state. Type the desired commands into the proper entry fields.
b) Lightware schema is for controlling the volume of the analog audio levels of the chosen audio port
RAP-B511 series – User's Manual
Step 3. Rotary LEDs give feedback about the current position of the jog dial knob. As it is rotated right (and
Volume Control Schema Table
Generic schemes collects the Lightware devices by the same audio setting commands.
Applied firmware package: v1.1.0b3b3 | LDC software: v2.5.1b5
in any Lightware device. The entry fields are inactive, because the command schema is loaded
automatically after setting the parameters:
The target device can be selected by typing the device type or chosen from the device list/
▪
generic schema list in a drop-down menu. For more details about the generic schema see
Volume Control Schema Table
Write the audio port number (e.g. I2 or O8)
▪
Click Set to confirm. Commands are loaded into the list.
▪
The Send unmute when volume changed option allows setting the volume while the controlled
▪
device is in muted state. If the option is enabled, the unmute command is sent, the LED is
switched off and the volume setting command is sent. If the option is unchecked, only the
volume setting is processed.
▪ Save the Schema by clicking Save Configuration to Device button. The configuration is saved to
Events in the Event Manager (one event for one level settings). It can be seen in the event list,
numbered backwards.
the volume increases), the LEDs turn on one-by-one. One level means half brightness.
Schema ID
DP-TPS-TX220
DVI-HDCP-TPS-TX220
FP-UMX-TPS-TX120, TX130
HDMI-3D-OPT-RX150RA
HDMI-3D-OPT-TX220
HDMI-TPS-RX110AY
Generic LWR-A HDMI-TPS-TX220
MMX4x2-HDMI
MMX4x2-HT200
SW4-OPT-TX240
SW4-TPS-TX240
UMX-TPS-TX120, -TX130, -TX140
WP-UMX-TPS-TX120, -TX130
MX2-16x16-DH-8DPi-A-R, MX2-24x24-DH-12DPi-A-R
MX2-24x24-DH-24DPio-A-R, MX2-24x24-HDMI20-Audio
MX2-24x24-HDMI20-Audio-R, MX2-32x32-DH-16DPi-A-R
MX2-32x32-HDMI20-A-R, MX2-48x48-DH-24DPio-A-R
Generic LWR-B MX2-48x48-DH-48DPio-A-R, MX2-48x48-HDMI20-A-R
MX2-8x4-HDMI20-CA, MX2-8x8-DH-4DPi-A
MX2-8x8-DH-8DPi-A, MX2-8x8-DH-8DPio-A
MX2-8x8-HDMI20-Audio, MX2-8x8-HDMI20-Audio-L
MX2-8x8-HDMI20-CA
MMX8x4-HT420M (mixer addon)
Generic LWR-C
MMX8x4-HT400MC (mixer addon)
38
Device Type