Table of Contents
Advertisement
Send Power toggle switch (see
H
DTP2 receiver configuration, set the toggle switch to the UP (Send Power) position on
the powered DTP2 unit to enable sending remote power to the far end. Set the toggle
switch to the DOWN (OFF) position on the DTP2 unit receiving power.
ATTENTION:
•
The DTP2 T 212 device is configured to output power to DTP2 models only.
If connected to a Legacy DTP or HDBT device, set the SEND POWER
toggle switch to the "DOWN" position (OFF). Failure to turn the power OFF will
damage the connected DTP device (see figure 3).
•
Le DTP2 T 212 est configuré pour fournir une alimentation aux modèles
DTP2 uniquement. S'il est connecté à un autre appareil, veuillez positionner
l'interrupteur à bascule sur « DOWN » (OFF). Si l'interrupteur n'est pas
positionné sur OFF, vous risquez d'entraîner la défaillance de l'appareil Legacy
DTP connecté (voir figure 3).
NOTE:
•
When the output is configured for DTP mode, remote power is available only if
both the transmitter and the receiver are from the DTP2 series.
•
When the output is configured for HDBT mode, remote power is not available
and both the transmitter and receiver require their own 12 VDC power supply.
Extron
DTP2 T 212
Transmitter
POWER
12V
1
2
A
AUDIO
2.0A MAX
Extron
DTP2 T 212
Transmitter
POWER
12V
1
2
A
AUDIO
2.0A MAX
Local
Power Supply
Local
Power Supply
Extron
DTP2 T 212
Transmitter
POWER
12V
1
2
A
AUDIO
2.0A MAX
Extron
DTP2 T 212
Transmitter
POWER
12V
1
2
A
AUDIO
2.0A MAX
Extron
DTP2 T 212
Transmitter
POWER
12V
1
2
A
AUDIO
2.0A MAX
Extron
DTP2 T 212
Transmitter
POWER
12V
1
2
A
AUDIO
2.0A MAX
Local
Power Supply
Figure 3.
Send Power Toggle Switch Configuration
Local
Power Supply
figure 2
on page 6) — In a DTP2 transmitter to
DTP Endpoint Connected to a DTP2 Endpoint
OFF
SEND
POWER
DTP Endpoint Connected to a DTP2 Endpoint
OFF
OFF
No Remote Power
SIG
LINK
CONTACT /
B
OVER TP
SEND
HDBT
TALLY
POWER
SEND
1
2
RS-232
RS-232
IR
POWER
OFF
Tx
Rx G
Tx
Rx
C G T
C G
T
+V
Tx
Rx
G
CATx Cable
OUT
DTP
up to 330' (100 m)
OFF
No Remote Power
CONTACT /
SIG
LINK
B
OVER TP
SEND
HDBT
TALLY
POWER
1
2
RS-232
IR
RS-232
OFF
C G T
C G
T
+V
Tx
Rx
G
OUT
DTP
Tx
Rx G
Tx
Rx
CATx Cable
up to 330' (100 m)
DTP2 Endpoint Connected to a DTP2 Endpoint
OFF
SEND
POWER
DTP2 Endpoint Connected to a DTP2 Endpoint
OFF
Direction of
OFF
Remote Power
SIG
LINK
CONTACT /
B
OVER TP
SEND
HDBT
TALLY
POWER
SEND
1
2
RS-232
RS-232
IR
POWER
OFF
Tx
Rx G
Tx
Rx
C G T
C G
T
+V
Tx
Rx
G
OUT
DTP
CATx Cable
up to 330' (100 m)
OFF
Direction of
Remote Power
CONTACT /
SIG
LINK
OVER TP
B
SEND
HDBT
TALLY
POWER
1
2
RS-232
RS-232
IR
OFF
C G T
C G
T
+V
Tx
Rx
G
OUT
DTP
Tx
Rx G
Tx
Rx
CATx Cable
up to 330' (100 m)
ON
SEND
POWER
Direction of
OFF
ON
Remote Power
CONTACT /
SIG
LINK
OVER TP
B
SEND
HDBT
TALLY
POWER
1
2
SEND
RS-232
RS-232
IR
POWER
OFF
C G T
C G
T
+V
Tx
Rx
G
OUT
DTP
Tx
Rx G
Tx
Rx
CATx Cable
up to 330' (100 m)
Direction of
OFF
Remote Power
CONTACT /
SIG
LINK
B
OVER TP
SEND
HDBT
TALLY
POWER
1
2
RS-232
RS-232
IR
OFF
Tx
Rx G
Tx
Rx
C G T
C G
T
+V
Tx
Rx
G
CATx Cable
OUT
DTP
up to 330' (100 m)
Extron
DTP HDMI 4K 330 Rx
Receiver
OVER DTP
RS-232
IR
Extron
Tx Rx
G
Tx Rx
DTP HDMI 330 Rx
DTP HDMI 4K 330 Rx
Receiver
OVER DTP
RS-232
IR
Local
Tx Rx
G
Tx Rx
DTP HDMI 330 Rx
Power Supply
Local
Power Supply
ON
SEND
POWER
Extron
DTP2 R 211
Receiver
OFF
ON
STATUS
SEND
INPUT
POWER
LINK
SEND
CONFIG
OUTPUT
POWER
Extron
OFF
DTP2 R 211
DTP2 R 211
Receiver
OFF
STATUS
SEND
INPUT
POWER
LINK
CONFIG
Local
OUTPUT
DTP2 R 211
OFF
Power Supply
OFF
SEND
POWER
Local
Extron
Power Supply
DTP2 R 211
Receiver
OFF
OFF
STATUS
SEND
INPUT
POWER
LINK
SEND
CONFIG
OUTPUT
POWER
Extron
OFF
DTP2 R 211
DTP2 R 211
Receiver
OFF
STATUS
SEND
INPUT
POWER
LINK
CONFIG
OUTPUT
DTP2 R 211
OFF
DTP2 T 212 • Installation
8
Advertisement
Table of Contents
