Cable Terminations - Honeywell NOTIFIER ID2000 Series Installation & Commissioning Manual

o
a b m n p
d e
k l
a g
b f
e
o p
l
m n
k
Name Name Function Function
a. a. OUT 1 OUT 1 Sounder Sounder
OUT 2 OUT 2 Sounder Sounder
b. b. OUT 3 OUT 3 Sounder/Volt-free Contact Sounder/Volt-free Contact
OUT 4 OUT 4 Sounder/Volt-free Contact Sounder/Volt-free Contact
c. c. INPUT 1 INPUT 1 Control Matrix Control Matrix
INPUT 2 INPUT 2 Control Matrix, Day/Night Control Matrix, Day/Night
Mode Remote Mode Remote
d. d. AUX 1 AUX 1 Auxiliary output Auxiliary output
e. e. AUX 2 AUX 2 Auxiliary output Auxiliary output
f. f. LOOP 1 LOOP 1 Loop circuit 1 OUT Loop circuit 1 OUT
LOOP 1 LOOP 1 Loop circuit 1 IN Loop circuit 1 IN
Loop circuit 2 OUT
g. g. LOOP 2 LOOP 2 Loop circuit 2 OUT
LOOP 2 LOOP 2 Loop circuit 2 IN Loop circuit 2 IN
ID2000 Series Installation & Commissioning Manual

3.1.1 Cable Terminations

This section provides some guidance on where to bring
cables into the back box for ease of termination.
a. The mains supply should be brought into the control
b. All loop and ancillary cable terminations should be
c. All loop and ancillary cable terminations should be
d. A row of knockouts, 'u', should be left to provide
The drawing below shows recommended points of entry
so that cabling can meet these requirements:
f
g q r
u s
h i
h i
q
r
t
Cable Cable Knockouts Knockouts
2-core 2-core a a
h. FAULT RELAY h. FAULT RELAY
2-core 2-core a a
i. i.
2-core 2-core b b
j. j.
2-core 2-core b b
2-core 2-core Any Spare Any Spare k/l. RS232/RS485 k/l. RS232/RS485
m-r LOOPs 3/4,5/6,7/8 m-r LOOPs 3/4,5/6,7/8
2-core 2-core Any Spare Any Spare
s. Fused Mains Block s. Fused Mains Block
2-core 2-core d d
t. t.
2-core 2-core e e
2-core 2-core f f
u. Leave Spare u. Leave Spare
2-core 2-core f f
2-core g
2-core g
2-core 2-core g g
panel where the cable path to the mains termination
block is kept as short as possible.
brought into the panel at suitable positions to ensure
tails are kept as short as possible.
brought into the panel at suitable positions to ensure
tails are kept as short as possible.
adequate mains supply input/signal cable
segregation.
The drawing shows the recommended points
of entry so that cabling can meet these
requirements.
Panel with internal PSU
i. Base PCB cabling/wiring terminations
using top-face knockouts 'a, b, f and g'.
ii. Base PCB cabling/wiring terminations
using rear knockouts 'd, e, h and i'.
iii. RS232 or RS485 cabling terminations using
rear knockouts 'k and l'.
iv. Loops 3/4, 5/6, 7/8 cabling using top face
knockouts 'm/n, o/p and q/r' respectively.
v. Power supply cable entry using knockouts
's'.
Panel with external PSU
As above except for item v above, which is
replaced with:
vi. DTP/Booster Module cabling using
knockouts 't'. See external PSU and DTP/
Booster Module instructions for details.
Name Name Function Function
Fault relay outputs Fault relay outputs
FIRE RELAY FIRE RELAY Fire relay outputs Fire relay outputs
COVER OFF COVER OFF Not supported Not supported
Comms circuits Comms circuits
As item f. As item f.
Termination of mains input Termination of mains input
External PSU External PSU DTP/Booster termination DTP/Booster termination
2 2
Mains/signal wiring segregation Mains/signal wiring segregation
1 - 1 -
NOT for the ID2002 Series Panels. NOT for the ID2002 Series Panels.
2 2
- Power supply cables (x2) and fault indication wiring. - Power supply cables (x2) and fault indication wiring.
3 3
- Recommended with internal PSU option. - Recommended with internal PSU option.
15
Cable Cable Knockouts Knockouts
2-core 2-core h h
2-core 2-core i i
- - - -
2-core 2-core k/l k/l
as item f. as item f. m-r m-r
3-core 3-core s s
1 1
3 x 2 cores 3 x 2 cores t t
- - u u
997-433-000-5, Issue 5
May 2010