Honeywell Farenhyt IFP-75HV Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Panel
  5. IFP-75HV
  6. Manual
Honeywell Farenhyt IFP-75HV Manual

Honeywell Farenhyt IFP-75HV Manual

Addressable fire alarm control panel
Hide thumbs Also See for Farenhyt IFP-75HV:
Table of Contents

Advertisement

Quick Links

Download this manual
IFP-75/IFP-75HV
Addressable Fire Alarm Control Panel
Manual
Farenhyt™ Series
Document LS10147-001SK-E Rev: E
4/6/2022 ECN: 151770

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Farenhyt IFP-75HV and is the answer not in the manual?

Questions and answers

Related Manuals for Honeywell Farenhyt IFP-75HV

Summary of Contents for Honeywell Farenhyt IFP-75HV

  • Page 1 Farenhyt™ Series IFP-75/IFP-75HV Addressable Fire Alarm Control Panel Manual Document LS10147-001SK-E Rev: E 4/6/2022 ECN: 151770...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke IMPORTANT! Smoke detectors must be installed in the same room detectors, heat detectors, manual pull stations, audible warning as the control panel and in rooms used by the system for the devices, and a fire alarm control panel (FACP) with remote...
  • Page 3 Farenhyt™ is a trademark; and Flexput®, Honeywell®, JumpStart®, Silent Knight® and SWIFT® are registered trademarks of Honeywell International Inc.Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.
  • Page 4 Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Introduction ..............................9 1.1: Basic System Overview.....................................9 1.1.1: Hardware Features ....................................9 1.1.2: Network System Hardware Features ..............................9 1.1.3: Software Features ....................................9 1.2: About this Manual......................................10 1.2.1: Terms Used in this Manual...................................10 1.3: Compatible Products......................................10 1.4: Related Documentation ....................................11 Section 2: Agency Listings, Approvals, and Requirements..................
  • Page 6 Table of Contents 4.12: 5865-3/5865-4 LED Annunciator Installation ...............................46 4.12.1: FACP Connection ....................................46 4.12.2: 5865 Mounting....................................47 4.13: Configuring Modules.....................................47 4.13.1: Assigning Module IDs..................................47 4.14: Telephone Connection ....................................48 4.15: Notification Appliance/Auxiliary Power Circuits ............................48 4.15.1: Conventional Notification Appliance ..............................49 4.16: Class A Notification Wiring...................................49 4.16.1: Auxiliary Power Installation................................50 4.17: Onboard Relays (Conventional) ..................................50 4.17.1: Common Trouble Relay ..................................51...
  • Page 7 Table of Contents 8.2: Modules ...........................................77 8.2.1: Edit Modules......................................77 8.2.2: Adding Modules ....................................78 8.2.3: Deleting Modules....................................78 8.2.4: View Module List ....................................78 8.3: Zone ..........................................78 8.3.1: Edit Zone ......................................78 8.3.2: View Zone Points ....................................82 8.4: Group ..........................................82 8.4.1: Edit Group ......................................82 8.4.2: View Group Points ....................................82 8.4.3: Edit Output Group Template ................................83 8.5: Point ..........................................83...
  • Page 8 Table of Contents 9.8.3: Erasing an F-Key Macro..................................107 9.8.4: Using a Recorded F-Key Macro .................................108 9.8.5: F-Key Status Event .....................................108 9.8.6: F-Key Map Inhibit ....................................108 Section 10: Reporting ..............................109 10.1: Receivers Compatible with the Control Panel.............................109 10.2: SIA / IFP-75 Panels PI Modifier Reporting..............................118 10.3: SIA–...

  • Page 9: Section 1: Introduction

    Section 1: Introduction The IFP-75, IFP-75HV, IFP-75B, and IFP-75HVBFire Alarm Control / Communicators are Addressable Fire Alarm Control Systems that meet the requirements of UL 864 10th Edition Standard. NOTE: All references to IFP-75 within this manual are applicable to the IFP-75, IFP-75B, IFP-75HV, and IFP-75HVB unless specified. 1.1 Basic System Overview 1.1.1 Hardware Features •...

  • Page 10: About This Manual

    Introduction About this Manual 1.2 About this Manual This manual is intended to be a complete reference for all installation and operation tasks for the IFP-75. 1.2.1 Terms Used in this Manual The following terminology is used with the IFP-75 system: Term Description Signaling Line Circuit...

  • Page 11: Related Documentation

    Related Documentation Introduction Type of Device Model Description Wireless WIDP-WGI Wireless Gateway WIDP-PHOTO Wireless Photoelectric Smoke Detector WIDP-ACCLIMATE Wireless Multi-criteria Smoke Detector WIDP-HEAT-ROR Wireless ROR Heat Detector WIDP-HEAT Wireless Fixed Heat (135°F) Detector WIDP-MONITOR Wireless Addressable Monitor Module WIDP-RELAY Wireless Addressable Relay Module B210W 6"...

  • Page 12: Section 2: Agency Listings, Approvals, And Requirements

    Testing and maintenance should be performed in compliance with NFPA 72. 2.1 Federal Communications Commission (FCC) The following information must be provided to the Telephone Company before the IFP-75can be connected to the phone lines: Manufacturer: Honeywell Model Number: IFP-75 FCC registration number: US: HS9AL10A2100 Ringer equivalence: 1.0A...

  • Page 13: Underwriters Laboratories (Ul)

    Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements CAUTION: INSTALLATION AND TEST TO ENSURE PROPER OPERATION, THIS EQUIPMENT MUST BE INSTALLED ACCORDING TO THE ENCLOSED INSTALLATION INSTRUCTIONS. TO VERIFY THAT THE EQUIPMENT IS OPERATING PROPERLY AND CAN SUCCESSFULLY REPORT AN ALARM, THIS EQUIPMENT MUST BE TESTED IMMEDIATELY AFTER INSTALLATION, AND PERIODICALLY THEREAFTER, ACCORDING TO THE ENCLOSED TEST INSTRUCTIONS.

  • Page 14: 6: Requirements For The Installation Of Carbon Monoxide (Co) Detection And Warning Equipment, Nfpa 720

    Agency Listings, Approvals, and Requirements Underwriters Laboratories (UL) 2.2.6 Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720 When using carbon monoxide detection the system must be monitored by a Supervising Station with emergency response, both aspects meet- ing the Standard for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 720.

  • Page 15: Section 3: Prerequisites For Installation

    System. Contact Technical Support with any ques- tions about software and the appropriate version for a specific application. The HFSS Honeywell Fire Software Suite is available at www.farenhyt.com.

  • Page 16: Calculating Current Draw And Standby Battery

    Prerequisites for Installation Calculating Current Draw and Standby Battery Label Rating Terminal No. Description Group Individual Voltage Current Terminal Block 2 SBUS – SBUS Power 27.4 VDC 0.5 A SBUS Communication 5 VDC 100 mA NAC1 – Notification Appliance Circuit/Auxiliary power 27.4 VDC 1 Amp NAC or Aux power NAC2...
  • Page 17 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current IDP-PHOTO-W/-IV IDP-PHOTO-T-W/-IV IDP-PHOTO-R-W/-IV IDP-HEAT-W/-IV Standby: 0.2 mA Alarm: 4.5 mA IDP-HEAT-HT-W/-IV IDP-HEAT-ROR-W/-IV IDP-PHOTO-CO-W IDP-CO-W IDP-BEAM (without integral test) Standby/Alarm: 2 mA Aux.
  • Page 18 Prerequisites for Installation Calculating Current Draw and Standby Battery Standby Device # of Devices Current per Device Alarm Current Current IDP-ZONE-6 Aux Pwr Standby 50 mA Alarm: 70 mA Standby 2.3 mA Alarm: 40 mA SLC Accessories B200SR/-W/-IV Sounder Base Aux Pwr Standby: 0.5 mA...

  • Page 19: 3: Current Draw Worksheet For Sk Slc Devices

    Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current Wireless Modules WIDP-WGI Wireless Gateway Max current using ext supply 40 mA Max current SLC Power 24 mA Total System Current Auxiliary Devices Refer to devices manual for current rating IPDACT-2 IP Communicator...
  • Page 20 Prerequisites for Installation Calculating Current Draw and Standby Battery Standby Device # of Devices Current per Device Alarm Current Current Standby 165 mA 165 mA Fire Panel (Current draw from battery) Alarm: 310 mA Addressable SLC Detectors SK-PHOTO SK-PHOTO-T SK-PHOTO-R Standby: 0.3 mA SK-HEAT...
  • Page 21 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current SK-RELAY-6 Standby: 1.9 mA Alarm: 32 mA SK-RELAYMON-2 Standby: 1.3 mA Alarm: 24 mA SK-ZONE Aux Pwr Standby 12 mA Alarm: 90 mA Standby:...
  • Page 22 Prerequisites for Installation Calculating Current Draw and Standby Battery Standby Device # of Devices Current per Device Alarm Current Current 5865-3 LED Annunciator Module Standby: 35 mA Alarm: 145 mA 5880 LED I/O Module Standby: 35 mA Alarm: 200 mA 5883 Relay Interface Standby: 0 mA...

  • Page 23: 4: Current Draw Worksheet For Sd Slc Devices

    Calculating Current Draw and Standby Battery Prerequisites for Installation 3.5.4 Current Draw Worksheet for SD SLC Devices Use Table 3.4 Table 3.4 to determine current requirements during the alarm/battery standby operation when the SD SLC devices are installed. You can install up to 75 SD devices per panel. Standby Device # of Devices...
  • Page 24 Prerequisites for Installation Calculating Current Draw and Standby Battery Standby Device # of Devices Current per Device Alarm Current Current 5865-3 LED Annunciator Module Standby: 35 mA Alarm: 145 mA 5880 LED I/O Module Standby: 35 mA Alarm: 200 mA 5883 Relay Interface Standby: 0 mA...
  • Page 25 Calculating Current Draw and Standby Battery Prerequisites for Installation Maximum Battery Standby Load Table 3.5 shows the maximum battery standby load for the IFP-75 based on 24 and 60 hours of standby. The standby load calculations of line G in the Current Draw Calculation Worksheets (Table 3.2, Table 3.3, and Table 3.4) must be less than the number shown in Table 3.5 for the battery size used and standby hours required.

  • Page 26: Section 4: Control Panel Installation

    Section 4: Control Panel Installation CAUTION: DISCONNECT POWER TO AVOID THE RISK OF ELECTRICAL SHOCK AND DAMAGE TO THE UNIT, POWER SHOULD BE OFF AT THE CONTROL PANEL WHILE INSTALLING OR SERVICING. 4.1 Mounting the Control Panel Cabinet Read the Environmental Specifications in Section 3.2 before mounting the IFP-75 panel. The IFP-75 cabinet base dimensions are: 12.531”...
  • Page 27 Mounting the Control Panel Cabinet Control Panel Installation Close the dead front panel. The bottom two screws on the annunciator will protrude through the dead front panel. Reinstall the top two annunciator screws removed in step 1. Insert the two screws with the star washers into the bottom of the cabinet to secure the dead front to the cabinet. remove top two annunciator screws from board and secure through dead front panel bottom two screws protrude...

  • Page 28: Board Assembly Diagram

    Control Panel Installation Board Assembly Diagram 4.2 Board Assembly Diagram The drawing below shows the location of components for FACP wiring. onboard annunciator DIP switch Power Input: IFP-75: 120VAC, 60Hz, 1.5A Ethernet IFP-75HV: 240VAC, 50/60 Hz, 1A Cellular connection battery connection phone line Form C...

  • Page 29: Ac Power Connection

    AC Power Connection Control Panel Installation AC input NAC circuits Phone lines Note: 0.25” spacing must be maintained between each of these circuit types; as well as between power-limited and non-power-limited circuits. Battery connection SBUS Relays Battery Battery Figure 4.4 Wire Routing Example 4.4 AC Power Connection At installation, connect the AC terminals to the power source as shown in Figure 4.5.

  • Page 30: Battery Power

    Control Panel Installation Battery Power PRI: 120V, 60Hz /240V, 50/60Hz, BLK-WHT SEC: 36V, 85VA YEL- 120/240V earth supervised AC input ground Figure 4.5 AC Power Connection 4.5 Battery Power The batteries must be sealed lead acid type. Before connecting the batteries to the FACP, make certain that the interconnect cable between the batteries is not connected.

  • Page 31: 1: Battery Accessory Cabinet

    Battery Power Control Panel Installation battery jumper (P/N 140694) shipped with pan black 12V battery 12V battery Figure 4.6 Battery Connection 4.5.1 Battery Accessory Cabinet The RBB Accessory cabinet can be used when your backup batteries requirements use backup batteries that are too large to fit into the main control panel cabinet.

  • Page 32: Wiring Specifications

    Control Panel Installation Wiring Specifications Connect the main control panel battery cables to the battery cable extenders as shown below. Figure 4.8 Splicing Control Panel Battery Cable to RBB Battery Cable Extenders Run extended battery cable from control panel cabinet through conduit to RBB cabinet as shown below. Connect battery leads to the backup battery terminals.

  • Page 33: 2: Calculating Wiring Distance For Sbus Modules

    Wiring Specifications Control Panel Installation 4.6.2 Calculating Wiring Distance for SBUS Modules The following instructions will guide you in determining the type of wire and the maximum wiring distance that can be used with SBUS accessory modules. To calculate the wire gauge that must be used to connect SBUS modules to the panel, it is necessary to calculate the total worst case current draw for all modules on a single 4-conductor bus.

  • Page 34: 3: Wiring Configurations

    Control Panel Installation Wiring Specifications Wire Gauge Ohms per 1000 feet (Rpu) 4.02 2.54 Table 4.9 Typical Wire Resistance Per 1,000 ft. Wiring Distance Calculation Example Suppose a system is configured with the following SBUS modules: 2 - RA-1000 Fire Annunciators 1 - 5496 Intelligent Power Expander 1 - 5865 LED Fire Annunciator 1 - 5824 Parallel/Serial Interface...

  • Page 35: Ra-100 Remote Annunciator Installation

    RA-100 Remote Annunciator Installation Control Panel Installation FACP SBUS Device 5495 or 5499 – + SLC IN SLC OUT SLC PROG NAC 1 SBUS NAC 2 OUT4 OUT3 OUT2 supervised, power-limited, Class B Figure 4.12 Powering SBUS Devices from 5495 or 5499 NOTE: The earth ground jumper on the 5495/5499 must be removed in this configuration.
  • Page 36 Control Panel Installation RA-100 Remote Annunciator Installation Flush Mounting Backbox dimensions are 9-9/32” W x 8-3/8” H. Minimum depth is 2". The backbox can be mounted prior to the complete installation of the RA-100 using any of the mounting holes shown below. mounting holes mounting holes Figure 4.14 RA-100 Backbox Mounting...

  • Page 37: 2: Ra-100 Connection To The Panel

    RA-1000 Remote Annunciator Installation Control Panel Installation Place the trim ring over the back box as shown below. Figure 4.16 Installing Trim Ring Attach the door assembly to the backbox using the screws provided. Refer to Figure 4.15. 4.7.2 RA-100 Connection to the Panel Connect the RA-100 to the panel as shown below.

  • Page 38: 1: Mounting The Ra-1000/R

    Control Panel Installation RA-1000 Remote Annunciator Installation RA-1000/R installation involves the following steps: Ensure the power is off at the panel. Mount the RA-1000/R in the desired location (see Section 4.8.1). Connect the RA-1000/R to the panel (see Figure 4.11). Use the DIP switches on the back of the RA-1000 to assign an ID# to the annunciator (see Section 4.13.1).
  • Page 39 RA-1000 Remote Annunciator Installation Control Panel Installation If an electrical box is used, the box must be 1-3/8” back from the face of the wall to accommodate the annunciator. Studs used with an elec- trical box must be 2x4” (or larger). Flush Mounting Steps ...

  • Page 40: Ra-2000 Remote Annunciator Installation

    Control Panel Installation RA-2000 Remote Annunciator Installation 4.9 RA-2000 Remote Annunciator Installation The optional RA-2000 Remote Annunciator can be surface or flush mounted. It is available in gray as RA-2000GRAY. Farenhyt™ Series BACK BACK BACK NEXT NEXT NEXT Model RA-2000 Figure 4.23 RA-2000 Remote Annunciator RA-2000 installation involves the following steps: Ensure power is off at the panel.
  • Page 41 RA-2000 Remote Annunciator Installation Control Panel Installation Attach the annunciator and door assembly to back box as shown below using the supplied screws. Figure 4.25 Attaching Annunciator / Door Assembly to Backbox Surface Mounting The RA-100TR Red Trim Ring kit and RA-100TG Gray Trim Ring kit are available for use when surface mounting the RA-2000. Remove the desired knockout.

  • Page 42: 2: Ra-2000 Connection To The Panel

    Control Panel Installation 5824 Serial/Parallel Printer Interface Module Installation 4.9.2 RA-2000 Connection to the Panel Connect the RA-2000 to the panel as shown below. SLC OUT SLC PROG NAC 1 TROUBLE SLC IN SBUS NAC 2 supervised, power-limited, Class B Figure 4.27 RA-2000 Connection to the Panel 4.10 5824 Serial/Parallel Printer Interface Module Installation The 5824 Serial/Parallel Printer Interface Module allows you to connect a printer to the panel.

  • Page 43: 5880 Led Driver Module

    5880 LED Driver Module Control Panel Installation Press ENTER to bypass the next two screens. A screen similar to the one shown below will display. Select Yes if printer should be supervised for Monitor Printer=Yes Out-of-Paper and Offline conditions. Output Port=Parallel Select type of printer, Parallel or Serial.

  • Page 44: 2: Facp Connection

    Control Panel Installation 5880 LED Driver Module 4.11.2 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown below. After the 5880 is connected to the panel, it must be added to the system. Programming is described in Section 8. 5880 NAC 1 TROUBLE...

  • Page 45: 4: Dry Contact Wiring

    5880 LED Driver Module Control Panel Installation Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 P3 and P4 are wired LEDs LED20 the same as P2.

  • Page 46: 5865-3/5865-4 Led Annunciator Installation

    Control Panel Installation 5865-3/5865-4 LED Annunciator Installation 4.12 5865-3/5865-4 LED Annunciator Installation The 5865-3 and 5865-4 are LED annunciators. The 5865-4 has 30 mappable LEDs, remote silence and reset key switches, and a general sys- tem trouble LED. The 5865-3 has 30 mappable LEDs only. These are arranged as 15 pairs of red (typically used for alarm) and yellow (typ- ically used for trouble) LEDs.

  • Page 47: 2: 5865 Mounting

    Configuring Modules Control Panel Installation 4.12.2 5865 Mounting Mount the 5865-4 to a standard 4-gang electrical box. Mount the 5865-3 to a standard 3-gang electrical box. In Figure 4.36, the 5865-4 is attached to a 4-gang box as an example. Attach the 5865 to a standard 3- or 4-gang electrical box.

  • Page 48: Telephone Connection

    4.14 Telephone Connection Connect the telephone lines as shown in Figure 4.39. Model 7860 phone cord is available from Honeywell for this purpose. A number of programmable options are available for customizing the telephone lines. These options are described in Section 8.6.

  • Page 49: 1: Conventional Notification Appliance

    Class A Notification Wiring Control Panel Installation 4.15.1 Conventional Notification Appliance This subsection of the manual explains how to install conventional notification appliances for Class A and Class B configurations. Class B Notification Wiring You must use an appliance from the list of compatible devices listed in the Device Compatibility Document, P/N: LS10167-003FH-E. To install a Class B notification appliance circuit: Wire Class B Notification appliances as shown below.

  • Page 50: 1: Auxiliary Power Installation

    Control Panel Installation Onboard Relays (Conventional) 4.16.1 Auxiliary Power Installation NAC Circuits 1 and 2 on the control panel can be used as auxiliary power circuits. The four types of auxiliary power available are: • Door Holder • Constant • Resettable Power •...

  • Page 51: 1: Common Trouble Relay

    Remote Station Applications Control Panel Installation NOTE: The N.C. contact is the relay contact that is closed when the panel has power and there are no alarm or trouble conditions. 4.17.1 Common Trouble Relay The control panel has a dedicated Form C trouble relay built into terminals labeled TROUBLE. The relay provides a normally open and a normally closed contact.

  • Page 52: 3: Nfpa 72 Polarity Reversal

    Control Panel Installation Remote Station Applications • Max Voltage: 27.4VDC • The maximum coil and wire resistance (combined) must not exceed 30 ohms. To install the 5220 for city box connection: Use one of the knockouts on the right side of the control panel to connect the 5220 using a short piece of conduit (must not exceed 20 feet in length).

  • Page 53: 4: Using A Mr-201/T Control Relay From Air Products

    Remote Station Applications Control Panel Installation Using the 7644-L8 Module When the 7644-L8 is used for polarity reversal, it allows alarm and trouble events to be reported to a remote site. Alarms will override trou- ble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. To install the 7644-L8 for polarity reversal: Wire the 7644-L8 to the control panel as shown in Figure 4.47.

  • Page 54: 5: Transmitter Activated By Dry Contacts

    Control Panel Installation Remote Station Applications Program the NAC circuit as a non silence NAC circuit (see Section 8.5.2). NOTE: If you need to transmit supervisory or trouble conditions, additional relay modules must be added. Use relay 1 to transmit supervisory conditions.

  • Page 55: Section 5: Networking

    Section 5: Networking 5.1 Network System Hardware Features 5.1.1 Networked Panels The IFP-75 panel can be networked to create a virtual system that is larger than 150 addressable points. Each additional IFP-75 provides another 150 addressable points to the network total. For example, a network of 32 IFP-75 panels provides a maximum addressable point capacity of 2,550 points (150 x 32= 4,800 IDP or SK devices).

  • Page 56: 1: Fiber Loop Modules

    Networking SK-NIC Installation 5.3.1 Fiber Loop Modules Two types of fiber-optic modules are available to use to transmit and receive communication with the SK-NIC. LED1 LED2 SK-FSL Single-Mode Fiber Module SK-FML Multi-Mode Fiber Module Figure 5.3 Types of Fiber Loop Modules The SK-FML (Fiber-Optic Multi-Mode) and SK-FSL (Fiber-Optic Single-Mode) are plug-in fiber loop modules.

  • Page 57: 1: Wiring

    SK-NIC Installation Networking Use the 6-pin cable included with SK-NIC to connect the IFP-75 to the SK-NIC. The 6-pin cable must be run in conduit between cabinets. Refer to Figure 5.1. LED1 LED2 Figure 5.5 Panel to SK-NIC Connection Each SK-NIC has the ability to monitor for earth ground faults on the twisted-pairs connected to Port 1 of its terminal block TB2. Earth fault detection for any wiring at Port 2 of TB2 is done at the next/previous SK-NIC due to these wiring connections being connected to Port 1 of TB2 at the next/previous SK-NIC.
  • Page 58 Networking SK-NIC Installation Fiber-Optic Multi-Mode Wiring between Multiple Panels Fiber-optic cable between multiple panels is shown in Figure 5.7 and Figure 5.8. Class X is shown with a dotted line.. port 2 last control panel/SK-NIC Class X wiring port 1 port 2 next control panel/SK-NIC port 1...

  • Page 59: Setting The Network Id For Each Panel

    Setting the Network ID for Each Panel Networking Fiber-Optic and Twisted Pair Wiring between Multiple Panels A mixture of fiber-optic cable and twisted-pair wiring between multiple panels is shown in Figure 5.9. Class X cabling is shown with a dot- ted line.

  • Page 60: Section 6: Network Management

    This section of the manual describes how to program the network options using the built-in annunciator. All options described in this section can be programmed using the HFSS Honeywell Fire Software Suite. HFSS must be used to edit site assignments.

  • Page 61: 4: Computer Access

    Network Programming Network Management This Menu will allow you to change the currently assigned Network Panel ID to the current Network ID DIP switch setting. The System will be down as the panel needs to reboot in order to complete the transition. When you use HFSS to program the panels, the Network Panel ID will be locked from future editing.

  • Page 62: Sync Network Options

    Network Management Sync Network Options The selections for this option are as follows: • pi modifier (default) • Panel ID* NOTE: *Only the SIA sends the Panel ID when reporting. Receiver Configuration The IFP-75Network can report events to as many as 68 receivers. See Appendix B for a list of the panel/receiver relationship numbers. Each receiver can be assigned the reporting credentials.
  • Page 63 Sync Network Options Network Management Select from which panel to source the options. Select Source Select Source Select Source 01= Panel 1 01= 07/28/21 12:20 OF 01=/28/21 12:20 OF8B 02= Panel 2 02 Panel 2 02 Panel 2 03= Panel 3 03 Panel 3 03 Panel 3 Select the line number.

  • Page 64: Network Management Quick Reference

    Network Management Network Management Quick Reference 6.4 Network Management Quick Reference Menu Options/Defaults Comments Learn Network Guest or member Add or remove panels See Section 6.2.1 into the network Edit Network Panel Names Network Panel ID Edit Panel Names See Section Names Site Names Edit Site Member...

  • Page 65: Section 7: Programming Overview

    Section 7: Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart auto-programming feature automates many programming tasks and selects the default options for the system.

  • Page 66: Mapping Overview

    & special optional system events Figure 7.1 Mapping Overview NOTE: Mapping cannot be programmed through the annunciators. It can only be programmed through the HFSS Honeywell Fire Software Suite. IFP-75 Series Manual — P/N LS10147-001SK-E:E 4/6/2022...

  • Page 67: 1: Input Point Mapping

    Mapping Overview Programming Overview 7.2.1 Input Point Mapping Input points are assigned to input zones. Any input point can be assigned to any input zone. Input points can be assigned to one zone only. An input point can be designated as “unused,” which means it has not been assigned to a zone. zone 1 point 1 point 2...
  • Page 68 Programming Overview Mapping Overview System Zone Panel Site Emergency Trouble SBUS Expander Trouble General Trouble Status Point Active SBUS Class A Trouble Site Silenced SLC Loop Trouble AC Loss Trouble F1 Key Active Advisory Battery Trouble F2 Key Active Ground Fault Trouble F3 Key Active Phone Line Trouble F4 Key Active...

  • Page 69: 4: Mapping Led Points

    7.3 Programming Using the HFSS Software Suite You can use the HFSS Honeywell Fire Software Suite to program the control panel on-site (the personnel will need to be on-site during the upload or download process). HFSS is a software package that lets you easily program the control panel using a Windows-based computer.

  • Page 70: 2: Moving Through The Menus

    Programming Overview Programming Menu Quick Reference 7.4.2 Moving through the Menus The first line of the display identifies the menu. The option available for editing displays next to the equal sign. Press the ENTER/ACK key to select the desired option. Arrows on the LCD indicate there are more options available. Access these screens by pressing the down arrow key.
  • Page 71 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference Edit Zone Name Section 8.3.1 *1-Count 2-Count Alarm Ver. Verification Type SNGL ILOCK Zone Properties DBL ILOCK 135° to 150°F Heat Temp Set 135° to 190°F Edit Zone Select Zone Zone Smoke Sensitivity Medium High...
  • Page 72 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference STATUS POINT CO DETECTOR SWITCH LATCH 1, 2, 3 SWITCH SUPERVISORY DETECTOR NON-LATCH SWITCH OUTPUT PT Select Group AUX CONST 1, 2, 3 NOTIF 1, 2 AUX RESET Select Module AUX DOOR Section 8.5.1 OUTPUT PT Select Group...
  • Page 73 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference No Accessory base SDR BAS Single station or Multi station Silence or Non- RLY BAS Silence Latch or non- ACCLIMATE latch, Single I-SdrBa station or Multi (Intelligent station, Silence Sounder Base) or Non-Silence, volume high (default) or low...
  • Page 74 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference No Accessory base SDR BAS Single station or Multi station Silence or Non- RLY BAS Silence CO ALARM/ Latch or non- FIRE ALARM latch, Single I-SdrBa station or Multi (Intelligent station, Silence Sounder Base) or Non-Silence, volume high...
  • Page 75 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference MANUAL PULL WATERFLOW FIRE SUPER- VISORY FIRE TAMPER FIRE DRILL SILENCE Latch and Non-Latch feature only RESET appear for WATERFLOW,FIRE B SWITCH P.A.S. ACK SUPERVISORY, FIRE TAMPER, ZONE AUX1, ZONE AUX2, ZONE AUX 1 SYSTEM AUX1, SYSTEM AUX2 ZONE AUX2...
  • Page 76 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference 75 sec, 90 Sec, 3 Ethernet Supervise min, 5 min, 1 hr, 24 *5 Minutes hrs, 30 days, None 24Hrs, 30 days, Cellular Supervise *24 Hours AlarmNet Timers none 10 min, 15 min, 30 Minutes, 1 hr, 2 hrs, Old Alarm Time *30 Minutes...

  • Page 77: Section 8: Programming

    This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection describes these menu options. All options described in this section can be performed using the HFSS Honeywell Fire Software Suite. NOTE: JumpStart auto-programming should be run Before any customized programming is performed. Thoroughly test the system after running JumpStart because it automatically programs the system, searching for and configuring all SLC and SBUS devices it finds.

  • Page 78: 2: Adding Modules

    Programming Zone 5880-LED I/O Default name for 5880 module Module ID: 03 (no customization) 5880 03_________ <Module Name> Use arrow keys to select characters. 5880-LED I/O Letters begin displaying with “A”. Press AB_____________ the ENTER key to select the desired character.
  • Page 79 Alarm Delay Characteristics  The programmed zone type is provided for user reference only. To modify the zone type, use the HFSS Honeywell Fire Software Suite. Table 8.2 lists the delay choices and a description of each type. Then, press ENTER.
  • Page 80 Programming Zone Type of Delay Description PAS-Positive Alarm This option is intended to be used with an acknowledge switch. An alarm is delayed for 15 seconds, giving on-site Sequence personnel a chance to investigate the alarm. If the acknowledge switch is not activated within 15 seconds, an alarm occurs automatically.
  • Page 81 Zone Programming Detector Type of Smoke Detector Choices Comments Protocol IDP/SK IDP-PHOTO, (3.5% obscurity) If the day/night sensitivity option is selected, you can have different sensitivity IDP-ACCLIMATE, settings during the day and at night. You can program the days of the week Medium (2.5% obscurity) IDP-PHOTO-T, that Day/Night Sensitivity will automatically adjust.

  • Page 82: 2: View Zone Points

    Programming Group NOTE: If the SLC protocol is changed from SD to IDP/SK series and the cadence is no longer valid for IDP/SK, the zone cadence will be set to constant on. For Local Zone, (choose Y or N, for Yes or No), 8.3.2 View Zone Points To view the points in a zone, follow these steps: Login to the panel.

  • Page 83: 3: Edit Output Group Template

    Point Programming Enter the group number, then press ENTER.. Group: G91 of 8 Point: 98:001 Number: 1 of 8 Figure 8.5 View Group Points 8.4.3 Edit Output Group Template Login to the panel. The panel will automatically access the Main Menu. Select 7 to access the Panel Programming.
  • Page 84 Programming Point Type Latching Function Comments Selection Option SK/IDP PHOTO DETECTOR PHOTO-HEAT HEAT PHOT DUCT 2WIRE SMK ACCLIMATE HEAT HT BEAM SK/IDP SUP SUP PHOTO DUCT Latching Supervisory switches can be latching or non-latching. DETECTOR Non Latching SUP SMOKE PHOTO SUP SMOKE ION SUP HEAT SUP ACCLIMATE...
  • Page 85 Point Programming Type Latching Function Comments Selection Option MAN_PULL Use this switch type for manual pull stations. This input is always latched. The switch can clear only when an alarm is reset. WATERFLOW Latching Use this switch type for monitoring water flow in a Sprinkler System. Switch closure will Non Latching cause a sprinkler alarm.

  • Page 86: 2: Point Programming For The Internal Or External Power Module

    Programming Point Type Latching Function Comments Selection Option OUTPUT PT Select Group Output Point, a general use notification type. Use for driving standard notification appliances. AUX CONST Use constant power for applications that require a constant auxiliary power source. Power is always present at Constant circuits.

  • Page 87: 3: Point Programming For 5880 And 5865 Modules

    Point Programming Function Selections Choices Type Selections Comments for each Type Enter Point or Circuit Select Type UNUSED NOTIF OUT CTRL CKT AUX PWR CONSTANT Constant auxiliary power. RESETTABLE Resettable auxiliary power. DOOR Door holder auxiliary power. AUX SYNC Sounder Sync auxiliary power for System Sensor B SWITCH* MAN PULL Refer to comments column of Table 8.4 for description of these options...

  • Page 88: 4: Point Programming For The 5496

    Programming System Options Enter the Point Number, then press ENTER. M01 P001 NOTIF Select NOTIF or UNUSED. Select the circuit to program. Select an output group for this notification point. Select a name for the point. MODULE_1 CKT_1 <Enter Pt or <=Exit> Figure 8.6 Programming Output Points Screen for 5880 and 5865 Modules Press the up or down arrows to select the type (Notification or unused).
  • Page 89  This option is used in conjunction with the HFSS Honeywell Fire Software Suite. Use the option to determine the number of rings before the panel answers a call from the computer. The range is 00-15 rings. This option is factory-programmed as 06 rings, which should be compati- ble for most installations, where the answering machine bypass feature is used.
  • Page 90  This option is used in conjunction with the HFSS Honeywell Fire Software Suite. This feature ensures that an answering machine will not interfere with communication between the panel and the computer. If an answering machine is used at the panel site, enable this feature; if an answering machine is not used, disable the feature.

  • Page 91: 2: Daytime/Nighttime Sensitivity

    System Options Programming Phone Line Gains Login to the panel. The panel will automatically access the main menu. Select 7 to access Panel Programming. Select 5 to access System Options. From the next menu, select 1 to access Communication Options. Select 5 to access Phone Line Gains.
  • Page 92 Programming System Options • low AC report delay • clock format • enable or disable automatic daylight savings time adjustment • AC clock frequency Waterflow Delay You can program a delay of 0-90 seconds (zero means no delay) to be used in conjunction with a waterflow switch. The delay is system- wide.

  • Page 93: 5: Miscellaneous Options

    System Options Programming Auto-Resound (4 or 24 hours) The system resound time period can be modified from the default value 24 hours to 4 hours. This setting adjusts when the FACP will auto- matically resound events after being silenced. Set this option to 4 hours when using SWIFT devices. 8.6.5 Miscellaneous Options Through this programming option, you can turn on or off strobe synchronization during silence, display status at Idle (auto display event), report by zone or point, and single key acknowledge.

  • Page 94: 7: Edit Banner

    Programming JumpStart Auto-Programming 8.6.7 Edit Banner The banner is the message that displays on the panel LCD when the system is normal. For example, a system is normal when no alarms or troubles exist and no one is currently using the system menus. You can create a custom message, which can be up to 40 characters, two lines of 20 characters each.

  • Page 95: Section 9: System Operation

    You can create a customized message that will display instead of the internal (default) message. See Section 8.6.7 for information to customize the banner. internal banner text Site 1 custom banner ABC Company example Honeywell IFP-75 Fire System ALL SYSTEMS NORMAL ALL SYSTEMS NORMAL 08/03/21 01:15:06PM 08/03/21 01:15:06PM Figure 9.2 Banner Display Examples 9.2 Menu System...

  • Page 96: 1: Panel Login Menu

    System Operation Menu System 9.2.1 Panel Login Menu After pressing ENTER, and 1 for the login menu, a screen will prompt for the type of access account, Administrator or User. An administra- tor has the ability to modify user accounts and view the cybersecurity log. The User account has access to panel programming. Admin Profiles After initial power-up, the IFP-75 requires a password change and user account setup before programming.

  • Page 97: 2: Main Menu Overview

    Menu System System Operation Type of Function Selectable Functions Panel Menus System Tests Fire Drill Menu Indicator Test Walk Test-No Report Walk Test -With Report Communicator Test Clear History Buffer Point Functions Disable/Enable Point Point Status Set SLC Device Address SLC Single Device Locater SLC Multiple Device Locater I/O Point Control...

  • Page 98: 3: Using The Menus

    System Operation Basic Operation 9.2.3 Using the Menus To move through the menus: Use up and down arrows to move through the options in a Menu. Use the left arrow key to move to a previous menu. To select an option: Enter the number of the option, OR press ENTER if the option appears at the top of the Menu (= symbol displays after the option number in this case).

  • Page 99: 4: Conduct A Fire Drill

    Basic Operation System Operation Single Key Acknowledge This feature allows the user to press the ACK key and display the oldest unacknowledged event in the system. If you press the ACK key again, it will acknowledge the event and then display the next oldest unacknowledged event without pressing the arrow keys. NOTE: This system has the capability to acknowledge across the ECS network.

  • Page 100: 8: Manual Alarmnet Registration

    System Operation Basic Operation 9.3.8 Manual AlarmNet Registration From the main menu, press 1 for System Tests. Select 8 to access Register AlarmNet. The screen will display and ask for confirmation. Feedback will be given if the command was sent or not. 9.3.9 Silence Alarms or Troubles When an alarm is sounding, press SILENCE and enter your code or rotate the key at the prompt.

  • Page 101: 12: View Status Of A Point

    Basic Operation System Operation Example of detector in compliance Example of detector not in compliance blanks indicate percent obscurity SMOKE PHOTO 2.5% SMOKE PHOTO ---% detector not in per foot compliance detector ID MODULE_33 POINT_4 MODULE_33 POINT_4 [Z001] [M33:004] A058 current value [Z001] [M33:004] A058 detector state...

  • Page 102: Operation Mode Behavior

    System Operation Operation Mode Behavior Feature Activation This Menu is used to activate/register additional features. Press 4 from the System Information menu. This will display the Feature Activation menu. Press 1 to enter a six-digit activation code or press 2 to review features already activated in this panel. Ethernet Info Screen From the System Information menu, press 5 to access the Ethernet Information.
  • Page 103 The activate the main menu. and programming menus current date and time display on the last line of the LCD. are not in use. Honeywell IFP-75 ALL SYSTEMS NORMAL 08/03/21 01:45:52PM Alarm The communicator seizes control of the phone line and Press the down arrow key to view the alarm.
  • Page 104 System Operation Panel Operating Modes Operating Occurs When System Behavior In This Mode You Can Mode Supervisory The communicator seizes control of the phone line and Press the down arrow key to view the supervisory calls the central station. condition. A screen similar to this one displays. The onboard annunciator sounds a loud, pulsing beep in device SUPERVSY: MAN_PULL...

  • Page 105: 1: Multi-Site Annunciator And Multi-Site User Access

    Releasing Operations System Operation Operating Occurs When System Behavior In This Mode You Can Mode Reset The RESET button is All LEDs are on briefly then the LCD displays “ALARM Menus are not available during the reset process. pressed followed by a RESET IN PROGRESS”.

  • Page 106: 1: Single Interlock Zone Releasing

    System Operation Releasing Operations + – Either NAC circuit can be used. UL-listed solenoid supervisory module- must be located at the solenoid. black releasing solenoid Use 1 solenoid per circuit. Figure 9.6 Wiring Configuration for Solenoid NOTE: For releasing operations, a manual releasing disconnect switch is required per UL 864. Refer to the MRD-1 Series Document for installation instructions.

  • Page 107: Smoke Alarm Verification

    Smoke Alarm Verification System Operation Conditions Required for a Release Output Activation Any release requires the activation of an interlock switch, and either a manual release switch or two activated addressable detectors. When these conditions are met, the “Release” and “General Alarm” outputs will activate, and the “Alert” output will deactivate. Inputs Output Results 1st Addressable Detector...

  • Page 108: 4: Using A Recorded F-Key Macro

    This option is programmable for each output group Map through the HFSS Honeywell Fire Software Suite. When an F-Key is active and a map in the system is set to be disabled by Map Inhibit, the system will show a trouble event.

  • Page 109: Section 10: Reporting

    ID formats. 10.1 Receivers Compatible with the Control Panel Table 10.1 shows receivers compatible with the control panel. Manufacturer Model Format Silent Knight by Honeywell Model 9800 SIA and Contact ID Model 9000 (SIA formats) Honeywell Security AlarmNet 7810-ir...
  • Page 110 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 111 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 112 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 113 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 114 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 115 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 116 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 117 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...

  • Page 118: Sia / Ifp-75 Panels Pi Modifier Reporting

    Reporting SIA / IFP-75 Panels PI Modifier Reporting 10.2 SIA / IFP-75 Panels PI Modifier Reporting Events are sent to the Central Station as a variable length string: The Event Format is: EEZZZZ Where the Event Format is defined as follows: Code Event Code Description Event Code (2 characters)

  • Page 119: Sia- Ifp-75 Panel Communicator

    SIA– IFP-75 Panel Communicator Reporting 10.3 SIA– IFP-75 Panel Communicator (Differences/additional features are underlined). Events are sent to the Central Station Receiver as a fixed length string. The event format is: EEPPMMZZZZ where the event format is defined as follows: Code Event Code Description Event code (2 characters)

  • Page 120: Section 11: Testing And Troubleshooting

    This section of the manual offers suggestions for troubleshooting hardware problems. Please read this section if you encounter a problem when you install the fire alarm control panel. If these suggestions do not solve your problem or if you encounter a problem that is not listed, contact Honeywell technical support for assistance. 11.2 Troubleshooting Common Problems...

  • Page 121: 2: Event History

    Built-in Troubleshooting and Testing Tools Testing and Troubleshooting Measure the battery voltage while the notification appliances are sounding. Replace any battery with terminal voltage less than 85% of rat- ing. Reapply the AC power and reset the system. 11.2.2 Event History The event history can be useful for tracking or recalling a trouble condition.

  • Page 122: 3: I/O Point Control

    Testing and Troubleshooting Earth Fault Resistance Press the left arrow key to exit the SLC multi-locater function. NOTE: The system will resume normal operation once you exit SLC Device Locater. 11.3.3 I/O Point Control This feature allows you to toggle any output on or off and trip any input device. This option can be useful to test a point’s output mapping. I/O Point Control can only be accessed if enabled in the user profile.

  • Page 123: Section 12: Installation Records

    Section 12: Installation Records Use this section of the manual as a reference list to track how points, zones, and groups are programmed. 12.1 SD SLC Device Point Record You can use Table 12.1 to keep track of SD SLC device points. Default addresses for ID: Onboard: = 97 Zone / Module Addr...

  • Page 124: Idp/Sk Slc Device Point Record

    Installation Records IDP/SK SLC Device Point Record 12.2 IDP/SK SLC Device Point Record You can use Table 12.2 and to keep track of IDP/SK SLC detectors and modules. Default addresses for ID: Onboard: = 97 Zone / Detector Addr Description Detector Addr Zone/ Group...

  • Page 125: Appendix A: Editing Text Using The Built-In Programmer

    Appendix A: Editing Text Using the Built-In Programmer This section contains the tables of programmable characters that may be used for the device, module, site, template, group, and zone names. T9 style editing is used. A.1 Characters Used for Editing Text Table A.1 lists the available characters and their associated numeric designator.

  • Page 126: Appendix B: Expanded Receiver/Panel Relationship

    Appendix B: Expanded Receiver/Panel Relationship The available Receiver Number will correspond with the panel number you entered. The Receiver Numbers are populated based on the panel number and they are audited to allow only the four appropriate receivers. See Section 6.2.6. Panel Available Receiver Numbers Table B.1 Receiver/Panel Relationship...

  • Page 127: Appendix C: Cadence Patterns

    Appendix C: Cadence Patterns Table C.1 shows the cadence patterns available for use with the control panel. Name Pattern Description (Patterns repeat until condition is cleared.) Constant Continuous sound (This is the only pattern that can be used for relay circuits. The system will override any other choice.) March Time 0.5 second on, 0.5 second off...

  • Page 128: Appendix D: Panel Security

    Appendix D: Panel Security Panel Installation / Maintenance Security Checklist System Description: ________________________________________________________________ System Location: __________________________________________________________________ Installer: _________________________________________________ Date: ___________________ Complete the following Cybersecurity Tasks for Each Panel Installation • Install the panel in a secure location considering both software and hardware vulnerabilities. •...

  • Page 129: Model Ifp-75/Ifp-75Hv Basic Operating Instructions

    Model IFP-75/IFP-75HV Basic Operating Instructions These instructions must be framed and displayed next to the IFP-75 Alarm Systems. Test the system in accordance to NFPA 72. panel in accordance with NFPA 72 fire code for Local Protected Fire Operation Task to Perform Silence Alarms and Troubles Press SILENCE and then enter a code if prompted.
  • Page 131 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 132 Honeywell Fire Systems 12 Clintonville Road Northford, CT 06472-1610 203-484-7161 LS10147-001SK-E | E | 04-22 www.farenhyt.com ©2022 Honeywell International Inc.

This manual is also suitable for:

Farenhyt ifp-75

Table of Contents

Save PDF