Download  Print this page

Honeywell NOTIFIER ID2000 Series Installation & Commissioning Manual

Hide thumbs

Advertisement

Quick Links

ID2000
installation &
commissioning
manual
997-433-000-5, Issue 5 May 2010

Advertisement

loading

  Also See for Honeywell NOTIFIER ID2000 Series

  Related Manuals for Honeywell NOTIFIER ID2000 Series

  Summary of Contents for Honeywell NOTIFIER ID2000 Series

  • Page 1 ID2000 installation & commissioning manual 997-433-000-5, Issue 5 May 2010...
  • Page 2 ID2000 Series Installation & Commissioning Manual The ID2000 Series Range of Fire Control Panel 997-433-000-5, Issue 5 May 2010...
  • Page 3: Table Of Contents

    ID2000 Series Installation & Commissioning Manual Contents The following markings are used either on the panel hardware or in the documentation. They have the following meaning: Introduction WARNING: Risk of electric CE Marking shock. Before working on mains connections, ensure System Design and Planning mains power supply to the Personnel...
  • Page 4 ID2000 Series Installation & Commissioning Manual EN54 Requirements 4.1.1 Loop Devices - Sensors and MCPs 4.1.2 Loop Devices - Isolators Loop Wiring Testing Panel Electronics Modules Introduction Kit PSU3A 5.2.1 Procedure Dual Transmission Path/Booster Module 23 Main Chassis 5.4.1 main Chassis Configurations 5.4.1 Procedure Extension Chassis 5.5.1 Zones 17-80 LED Extension Chassis...
  • Page 5 ID2000 Series Installation & Commissioning Manual Powering the Panel External Wiring 8.4.1 Introduction 8.4.2 Loop Checks Before Connecting Wiring 43 8.4.3 Connecting the Loop Wiring to the Panel 44 8.4.4 Loop Checks After Connecting Wiring 44 8.4.5 24V Auxiliary Outputs Check 8.4.6 Sounder Circuits Check 8.4.7 Fault Relay Wiring Batteries...
  • Page 6: Introduction

    ID2000 Series Installation & Commissioning Manual Introduction The purpose of this manual is to provide the user with all recommended procedure descriptions and full technical details for the successful installation and commissioning of NOTIFIER’s ID2000 Series stand-alone fire alarm controllers and repeaters or for a complete ID2000 Series integrated Fire Control System.
  • Page 7: General

    ID2000 Series Installation & Commissioning Manual 1.4 General The ID2000 Series of intelligent fire alarm controllers are designed for use with NOTIFIER’s range of addressable analogue sensors, control and monitoring modules and addressable call points. A unique signalling protocol is used, having digital address and control signals, and analogue pulse width monitoring for the reply data from devices.
  • Page 8: Installation Guide

    ID2000 Series Installation & Commissioning Manual Installation Guide 2.1 How to Use this Guide This Installation Guide is intended to provide you with simple guidelines on how to install an ID2000 Series fire control panel or system, quickly and safely. For each stage in the ID2000 Series panel installation and commissioning procedures a brief description is given of its purpose, complete with detail drawings, flow...
  • Page 9: Glossary Of Icons

    ID2000 Series Installation & Commissioning Manual 2.1.4 Glossary of Icons Throughout this Installation and Commissioning Manual and other supplied user documentation a number of simple icons are used, either on their own or together with larger illustrations, to simplify a particular task or process.
  • Page 10: Pre-Installation Check List

    ID2000 Series Installation & Commissioning Manual 2.2 Pre-installation Check List Before installing the ID2000 equipment or fitting sensors, you must first ensure that the following criteria have been met. Failure to do this may not only result in damage to the equipment, but may also cause problems when commissioning the equipment or adversely affect its performance.
  • Page 11: Transient Protection

    ID2000 Series Installation & Commissioning Manual f) DO NOT site the panel where there would be restricted access to the internal equipment and cabling/wiring connections. 2.3 Transient Protection This equipment contains transient-protection devices. Although no system is completely immune from lightning transients and interference, for these devices to function correctly, and to reduce susceptibility, this equipment must be earthed correctly.
  • Page 12: Installation

    ID2000 Series Installation & Commissioning Manual 2.4 Installation The ID2000 Series of modular fire control panels are relatively simple to install providing the recommended procedures described in this Installation Guide are followed. To avoid damage to the control panel ensure that Follow all installation instructions described in this you follow these manual.
  • Page 13: What To Do If Your Module Is Damaged

    ID2000 Series Installation & Commissioning Manual 2.4.2 What to do if Your Module is Damaged or Suspect If you have problems regarding the quality of any supplied order items including the control panel, its ancillaries or this manual or items are missing, follow the procedure below.
  • Page 14: Back Box Fixing

    ID2000 Series Installation & Commissioning Manual 2.4.3 Back Box Fixing The ID2000 Series control panel back boxes are available 122mm deep and 220mm (external dimensions including fixing dimples). Where required, the deeper back boxes allow the fitting of high-capacity-rated batteries as defined in Section 7.5 Batteries and internally-mounted PSUs other than the 3A-rated version.
  • Page 15: Electronics Modules

    ID2000 Series Installation & Commissioning Manual 2 Using a suitable-sized drilling bit - for holes to take up to 6mm (No.12-sized) wood screws - drill the required DO NOT use the back number of holes. box as a guide when drilling.
  • Page 16: Replacing The Electronics Modules

    ID2000 Series Installation & Commissioning Manual This procedure MUST be followed: 1 Fit the PSU to the main chassis - refer to Section 5.2 To avoid damage to the for details. electronics, remove trades’ 2 Fit the main chassis to the back box - refer to Section operation debris before 5.3 for details.
  • Page 17: Mounded Front Covers

    ID2000 Series Installation & Commissioning Manual 2.7 Moulded Front Covers The ID2000 Series control panel is supplied with one, two or three moulded front covers, depending upon your panel configuration. Two moulded cover types are available; the main and extension. All panel sizes require a main cover kit (PN: 020-480).
  • Page 18 ID2000 Series Installation & Commissioning Manual 2 Prior to fitting the cover, if a printer is installed ensure that you have allowed a sufficient length of printer paper to be pulled through the cover aperture. ) i ( 3 Fit the appropriate plate over the printer paper exit ) i i aperture.
  • Page 19: Cabling

    ID2000 Series Installation & Commissioning Manual Cabling 3.1 Cabling Instructions All wiring should comply with current IEE wiring WARNING Risk of electric regulations, (BS7671), or the applicable local wiring shock. Before working on regulations. Note also the requirements of EN 54-14 for mains connections, ensure cabling and interconnection of a fire detection and alarm mains power supply to the...
  • Page 20: Cable Terminations

    ID2000 Series Installation & Commissioning Manual 3.1.1 Cable Terminations This section provides some guidance on where to bring cables into the back box for ease of termination. a. The mains supply should be brought into the control panel where the cable path to the mains termination block is kept as short as possible.
  • Page 21: Cable Installation Notes

    ID2000 Series Installation & Commissioning Manual 3.2 Cable Installation Notes 3.2.1 Introduction The following notes are intended to assist installers of analogue addressable control systems. They have been produced from information derived from the supplier's technical resource and from information fed back concerning existing systems.
  • Page 22: Emc Considerations

    ID2000 Series Installation & Commissioning Manual 3.3 EMC Considerations Following the above instructions and by using suitable cables EMC problems will be avoided. In particularly difficult EMC environments, or where non-preferred cabling is used, it is possible to fit additional ferrite suppressors (sleeves) to cables entering the control panel.
  • Page 23: Sensors And Modules

    ID2000 Series Installation & Commissioning Manual Sensors and Modules Each of these devices is packaged with an instruction leaflet showing the correct interconnections for various applications. OPAL Protocol may be used but are supported in CLIP polling mode only. To include the internal isolator (not all OPAL devices incorporate these) use the B501 AP sensor base which has an additional positive leg loop wiring connector for the device’s internal isolator.
  • Page 24: Panel Electronics Modules

    ID2000 Series Installation & Commissioning Manual Panel Electronics Modules 5.1 Introduction This section describes how to install the ID2000 Series panel electronics, i.e. the Power Supply Unit (PSU) and the main chassis, which contains all processing PCBs To avoid damage to the and the optional PRN-ID printer.
  • Page 25: Kit Psu3A

    ID2000 Series Installation & Commissioning Manual 5.2 Kit PSU3A The Kit PSU3A module is very easy to fit to the main chassis, providing the instructions described below are followed. The PSU is located in an open, rear compartment of the main chassis and MUST be fitted before installing the main chassis in the back box.
  • Page 26 ID2000 Series Installation & Commissioning Manual 5.2.1.1 Main Chassis Wiring Connections 3 Connect the 10-way ribbon cable (G) and the power cable (H) to the PSU3A. The power cable connects at two positions, as shown. T E M 4 Ease the connectors of these cables and the ferrite through the aperture (I) in the main chassis.
  • Page 27 ID2000 Series Installation & Commissioning Manual 5.2.1.2 Mains and Safety Earth Wiring Connections WARNING! WARNING: Before proceeding, refer to the cabling Isolate mains power instructions given in Section 3.1. Isolate before proceeding. mains power. Note that fuse information is given in Appendix 1 Section 1.2. TRANSIT CABLE CLIP: Before proceeding, CAREFULLY cut the cable clip that secures the ferrite cable loop to the front of the back box.
  • Page 28: Dual Transmission Path/Booster Module

    ID2000 Series Installation & Commissioning Manual 5.3 Dual Transmission Path/Booster Module The Dual Transmission Path (DTP)/Booster module is very easy to fit to the main chassis, providing the instructions described below are followed. The DTP/Booster module is located in an open, rear compartment of the main chassis and MUST be fitted before installing the main chassis in the back box.
  • Page 29 ID2000 Series Installation & Commissioning Manual The illustration at left shows the DTP/Booster module correctly located in the main chassis. 5.3.1.1 Main Chassis Wiring Connections Once the DTP/Booster module is fitted to the main chassis, the two wiring assemblies that are held by the grommet should now be terminated on the Base PCB connection sockets as follows: a.
  • Page 30: Main Chassis

    ID2000 Series Installation & Commissioning Manual 5.4 Main Chassis The ID2000 Series control panel main chassis provides the following features: DO NOT fit the main chassis in the back box a. System control and monitoring function PCBs until the PSU module has b.
  • Page 31: Extension Chassis

    ID2000 Series Installation & Commissioning Manual 5.5 Extension Chassis The ID2000 Series extension chassis is required for CAUTION! zones 17-80 LEDs and/or for mounting the ID2000 Series Make sure ALL power to PRN-ID printer. The extension chassis is very simple to the panel has been fit providing the instructions below are followed.
  • Page 32: Prn-Id Printer

    ID2000 Series Installation & Commissioning Manual 5.6 PRN-ID Printer The printer is supplied one of two ways: a. For panels with more than 16 zonal LEDs, the printer first has to be fitted to the extension chassis (refer to installation instructions 997-452, supplied with the printer) and then the combined assembly secured to the back box.
  • Page 33: Printer Used With Stainless Steel Cover

    ID2000 Series Installation & Commissioning Manual 5 To re-align the paper exit path: Locate the paper release control (Q) immediately to the left of the paper exit slot and pull the top lug outwards and down through approximately 90 . With the lug in this position the paper alignment can now be adjusted.
  • Page 34: Display Pcb

    ID2000 Series Installation & Commissioning Manual 5.7 Display PCB The Display PCB is located on the inner face of the main WARNING - chassis door. In the unlikely event that the Display PCB Disconnect power from becomes faulty and needs to be replaced, the front door the ID2000 and assembly, supplied as part of a kit (PN: 020-491-XXX) remove batteries...
  • Page 35: Base Pcb

    ID2000 Series Installation & Commissioning Manual 5.8 Base PCB The ID2000 Series Base PCB is located on the rear face WARNING - of the main chassis PCB enclosure. In the unlikely event Disconnect power that the Base PCB becomes faulty and needs to be replaced from the ID2000 a replacement kit (PN: 020-568) is available.
  • Page 36: Fitting The Replacement Base Pcb

    ID2000 Series Installation & Commissioning Manual 5.8.1 Fitting the Replacement Base PCB DO NOT use a screwdriver to lever the 10 Taking suitable anti-static precautions and with the replacement Base PCB orientated correctly, offer it PCB away from the to the main chassis PCB enclosure. With the locating main chassis.
  • Page 37: Processor Pcb

    ID2000 Series Installation & Commissioning Manual 5.9 Processor PCB The ID2000 Series Processor PCB controls and monitors all Make sure you have ID2000 Series Control Panel processing functions. The a PC back-up of the Processor PCB is electrically connected to the Display PCB current and the Base PCB.
  • Page 38: Loop Interface Pcb

    ID2000 Series Installation & Commissioning Manual 5.10 Loop Interface PCB The Loop Interface PCB (PN: 124-323) provides two additional fire detection device loops. The Loop Interface PCB is located Make sure you have within the main chassis PCB enclosure, adjacent to the Base a PC back-up of the PCB.
  • Page 39: Isolated Rs232 Interface Pcb

    ID2000 Series Installation & Commissioning Manual 5.11 Isolated RS232 Interface PCB The ID2000 Series Isolated RS232 Interface PCB Make sure you have (PN: 124-300) enables connection of the ID2000 Series a PC back-up of the Fire Control Panel to an external printer, terminal or third- current party-protocol station.
  • Page 40: Cables And Wiring

    ID2000 Series Installation & Commissioning Manual 5.11.1 Cables and Wiring 9 Make the following wiring connections to the Isolated RS232 Interface PCB: Ribbon cable at socket SK2 from the Base PCB socket SK12 or SK13. ii Use a screened multi-core cable (see 3.2.2 for recommended types) to connect external third-party equipment.
  • Page 41: Isolated Rs485 Interface Pcb

    ID2000 Series Installation & Commissioning Manual 5.12 Isolated RS485 Interface PCB The ID2000 Series Isolated RS485 Interface PCB Make sure you have (PN: 124-247) enables the ID2000 Series Fire Control Panel a PC back-up of the to be networked to other ID2000 Series control panels or for current connection to ID2000 Series repeater panels.
  • Page 42: 1Cables And Wiring

    ID2000 Series Installation & Commissioning Manual 5.12.1 Cables and Wiring 9 Make the following wiring connections to the Isolated RS485 Interface PCB: Ribbon cable at socket SK2 from the Base PCB socket SK12 or SK13. Apply power ii Cable at socket SK1 from the next station on the BEFORE making network (as applicable).
  • Page 43: Repeaters And Network

    ID2000 Series Installation & Commissioning Manual Repeaters and Network EN54-2: 12.5 Integrity of transmission paths. Repeaters can be connected to the ID2000 Series panel This network does not via an RS485 serial data link. This link can also be provide the required used to network slave terminals to the panel.
  • Page 44: Network Connections

    ID2000 Series Installation & Commissioning Manual 6.2 Network Connections An ID2000 Series Network master terminal can be networked with up to seven Network slave terminals, master repeaters and slave repeaters to a maximum of thirty one components. The Network master and slave terminals use RS485 signalling to communicate with each other and with the repeaters.
  • Page 45: Vdu

    ID2000 Series Installation & Commissioning Manual A suitable VDU may be connected to any ID2000 Series panel at SK19 on the Base PCB or to the Isolated RS232 Interface PCB, if fitted, using socket SK1. The recommended VDU may be obtained from NOTIFIER (order code: CRT-2).
  • Page 46: Commissioning

    ID2000 Series Installation & Commissioning Manual Commissioning 8.1 Introduction To bring the panel into an operational state ready for configuration, follow the steps detailed below. Information on how to configure the panel is given in the ID2000 Series Panel Configuration Manual (ref. 997- 435-XXX).
  • Page 47: Powering The Panel

    ID2000 Series Installation & Commissioning Manual 8.3 Powering the Panel 1 Connecting power, ALL front panel LED indicators should be extinguished with the exception of the green ‘POWER’ LED. 2 View the liquid crystal display. It should momentarily display the start-up message ‘NOTIFIER ID200x Version x.xx Intelligent Fire Detection System’...
  • Page 48: Loop Checks Before Connecting Wiring

    ID2000 Series Installation & Commissioning Manual 8.4.2 Loop Checks Before Connecting Wiring Typical connections of analogue addressable devices to a loop are shown below. B501/B501 AP (see Note 3) B501/B501 AP (see Note 3) Loop Loop LOOP IN LOOP OUT Start Start Monitor used...
  • Page 49: Connecting The Loop Wiring To The Panel

    ID2000 Series Installation & Commissioning Manual Appendix 3 of this manual or the LBC for OPAL device types fitted with internal isolators. The following tests should then be carried out using a multimeter. 2 Check the continuity of each leg of the loop and measure the end-to-end resistance.
  • Page 50: Auxiliary Outputs Check

    ID2000 Series Installation & Commissioning Manual 8.4.5 24V Auxiliary Outputs Check There are two monitored 24V Auxiliary Outputs. Before connecting any circuit to either of these outputs check that: a. The external wiring is not short circuit. b. There are no forward-biased diodes (as used for example with end-of line power monitoring relays) connected across the external wiring.
  • Page 51: Batteries

    ID2000 Series Installation & Commissioning Manual 8.5 Batteries Back Box Size Yuasa The ID2000 Series control panel is designed for optimum performance when used with either the Yuasa-NP range Standard back box 12Ah of backup batteries. The panel back boxes have space Extended/double provision for two 12V batteries;...
  • Page 52: Battery Disposal

    ID2000 Series Installation & Commissioning Manual 8.5.2 Battery Disposal As a minimum, replace the batteries every four years. The battery units should always be disposed of in accordance with the battery manufacturer ’s recommendations and local regulations. EN54-2 : 8.2.4c. Earth Fault Monitoring 8.6 Earth Fault Monitoring is required.
  • Page 53: Volt-Free Contact Output Option

    ID2000 Series Installation & Commissioning Manual 8.7 Volt-free Contact Output Option Two ID2000 Series control panel sounder circuits, i.e. sounder circuits 3 and 4, can be configured to provide a volt-free, normally-open or normally-closed contact. For either sounder circuit, the configuration changes are carried out on the Base PCB simply by moving upto two jumper links and removing the sounder circuit’s associated fuse.
  • Page 54: Maintenance

    ID2000 Series Installation & Commissioning Manual Maintenance Create a logbook in accordance with the recommendations of EN54 Part 14. This logbook should be used and maintained for recording events as described below. 9.1 Routine Testing In order to ensure that the system is fully operational, and to comply with the requirements of EN54 Part 14 and BS 5839 Part 1: 1988, the following routine attention is recommended:...
  • Page 55: Appendix 1 Fault Messages And Possible Meanings

    ID2000 Series Installation & Commissioning Manual Appendix 1 FAULT MESSAGES AND POSSIBLE MEANINGS 1.1 Fault Messages - Possible Causes & Remedies 1.1.1 Loop Faults Loop Card Hardware System Fault 1 - Loop-CPU Fault Driver Fault Panel Fault 5 - Power Restart System Fault 29 - LIB ROM Checksum These fault messages indicate a loop PCB failure.
  • Page 56 ID2000 Series Installation & Commissioning Manual Signal Degraded Data returned from a loop device is being corrupted over a period of time. Action: Check a.The continuity of loop screens. b.The screen is connected to earth at one point only (normally at the panel). Note: The default time is one hour.
  • Page 57 ID2000 Series Installation & Commissioning Manual 1.1.4 Processor Faults System Fault 40 - Main CPU Watchdog Operated System Fault 41 - EPROM Memory Checksum System Fault 42 - E2PROM Memory Write Error System Fault 43 - FLASH Memory Checksum System Fault 45 - FLASH Memory Write Error System Fault 46 - Software error Panel Fault 49 - CPU Watchdog timer fault System Fault 64 - CPU Watchdog not enabled...
  • Page 58 ID2000 Series Installation & Commissioning Manual 1.1.6 Printer Faults Printer Fault Internal printer only. This fault may be an indication of a paper jam or malfunction, no paper, or the printer disconnected. Note: The printer operation is only monitored if the printer was functional at the last power-on.
  • Page 59 ID2000 Series Installation & Commissioning Manual 1.1.8 Other Faults Earth Fault The earth fault monitor detects the presence of an earth on the positive or negative sides of the system. Should this condition occur, disconnect the field circuit wiring one cable at a time and view the LED at the top right of the Base PCB;...
  • Page 60: Appendix 2 Specifications

    ID2000 Series Installation & Commissioning Manual Appendix 2 - Specifications ID2000 Series Panel Range General: The Fire Control Panel meets the requirements of EN 54-2/4. See Section 1.1 CE Marking for further details. Mechanical: Construction: Sheet steel enclosure with panel main components supplied as separate build modules.
  • Page 61 ID2000 Series Installation & Commissioning Manual Displays and Indications: Alphanumeric display: 2-line x 40-character back-lit LCD LED Status Indicators: DISABLEMENT, TEST, EARTH FAULT, POWER SUPPLY FAULT, SYSTEM FAULT, POWER, PRE- ALARM, SOUNDERS DISABLED, SOUNDER FAULT, DELAY ACTIVE, DAY MODE. Zone Indicators: Individual FIRE and Fault indicators for 16 or 80 zones (depending upon configuration options).
  • Page 62 ID2000 Series Installation & Commissioning Manual Power Supply Unit (PSU) Kit PSU7A (PN:020-579). For specification details, refer to 997-277-000-X (PSU7A installation) and 997-267-000-X (DTP/Booster Installation) Kit PSU3A (PN: 020-648) Maximum current consumption: 1.6A Output ratings: Output voltage: 26.0Vdc-28.3V dc (PSU3A Unboosted output not used in ID2000) Ripple voltage: ±300mV Max.
  • Page 63 ID2000 Series Installation & Commissioning Manual Sounder Output Rating Type: Voltage reversal Output voltage: 26 to 28V when active; -6.8V to -9V when inactive * Total system load is limited by the Maximum load: 1A * available PSU output. The NOTIFIER Fuse rating T 1A 250V Loop and Battery Calculator Support...
  • Page 64 ID2000 Series Installation & Commissioning Manual Programming Configuration methods: Front panel key-pad; VDU terminal connected to RS232 port; Off-line using PC-Upload/ Download program. Configuration access: Key-pad access is passcode- protected (user-definable) for all configuration options. Refer to the ID2000 Series Panel Configuration Manual (ref.
  • Page 65: Appendix 3 Id2000 System Design Guide

    ID2000 Series Installation & Commissioning Manual Appendix 3 ID2000 System Design Guide The following rules give a simplified way to ensure that a system design will operate correctly. This guide uses worst case figures and simplifies many of the calculations to ensure that a design which adheres to this guide will work when installed correctly.
  • Page 66 ID2000 Series Installation & Commissioning Manual Compatible CLIP Protocol Loop Devices: Sensors Modules CPX-551E Standard Ionisation Sensor M500KACGB Manual Call Point CPX-751E Low Profile Ionisation Sensor M500KACW Weatherproof Manual Call Point FSL-751E VIEW laser-based smoke sensor M500KACEU EU-style Manual Call Point LPX-751 VIEW laser-based smoke sensor (low profile) M700KAC-FG Manual Call Point - non-isolated...
  • Page 67 ID2000 Series Installation & Commissioning Manual Recommended Cables All cables connected to the fire alarm control panel must be fire resistant cables. Shielded cable must be used for signalling loops and sounder circuits. The drain earth wire should be connected to a suitable earth bonding point at both ends of the cable.
  • Page 68 Charles Avenue T: +44 (0) 1444 230 300 Burgess Hill F: +44 (0) 1444 230 888 W. Sussex E: sales@notifierfiresystems.co.uk RH15 9UF www.notifierfiresystems.co.uk local distributor Quality Systems Certificate No. 154 Assessed to ISO9001 Every care has been taken in the preparation of this document but no liability can be accepted for the use of the information therein. Design features may be changed or amended without prior notice.

This manual is also suitable for:

Notifier id2002