Siemens SINUMERIK 840D sl Programming Manual page 1176

Work preparation
3.25 Programming cycles externally
No Screen Cycle pa‐
. form pa‐ rameter
rameter
2 Selection
S_KNUM
3 Icon+
S_PRNUM
number
4 L1/X1
S_SETV0
5 L2/Y1
S_SETV1
6 L3/X2
S_SETV2
7 L4/Y2
S_SETV3
8 XP/X3
S_SETV4
9 XP/Y3
S_SETV5
10 X4
S_SETV6
11 Y4
S_SETV7
12 X0
S_SETV8
13 Y0
S_SETV9
14 α0
S_STA1
15 α1
S_INCA
16 DZ
S_ID
1176
Meaning
Correction of work offset (WO) or basic WO or basic reference
Val‐ UNITS:
ues:
TENS:
0 = No correction
1 to max. 99 numbers of the work offset or
1 to max. 16 numbers of the basic offset
HUNDREDS: Reserved
THOUSANDS: Correction of WO or basic or basic reference
0 = Correction of the adjustable WO
1 = Correction of the channel-specific basic WO
2 = Correction of the basic reference
9 = Correction of the active WO or for G500 in last active channel-specific basic WO
TEN THOUSANDS: Coarse or fine correction in the WO, basic WO or basic refer‐
ence
0 = Fine correction
1 = Coarse correction
Number of the field of the probe parameters (not probe number)
(value range 1 to 40)
Distance L1 between the pole and measuring point P1 in the direction of the 1st axis of the
plane (for G17 X)
3)
(if the actual distance L1=0, then L1 = M_SETV1 / 2 is automatically calculated) or
starting point P1x of the 1st axis of the plane (for G17 X)
Distance L2 between the pole and measuring point P2 in the direction of the 1st axis of the
plane
3)
or starting point P1y of the 2nd axis of the plane (for G17 Y)
Distance L3 between the pole and measuring point P3 in the direction of the 2nd axis of the
plane
3)
(if the distance L3=0, then for a corner that is not right angled, L3 = M_SETV3 / 2 is auto‐
matically calculated)
or starting point P2x of the 1st axis of the plane
Distance L4 between the pole and measuring point P3 in the direction of the 2nd axis of the
plane with a corner that is not right angled
or starting point P2y of the 2nd axis of the plane
Position of the pole in the 1st axis of the plane
or starting point P3x of the 1st axis of the plane
Position of the pole in the 2nd axis of the plane
or starting point P3y of the 2nd axis of the plane
Starting point P4x of the 1st axis of the plane
Starting point P4y of the 2nd axis of the plane
Setpoint of the measured corner in the 1st axis of the plane for correcting in WO
Setpoint of the measured corner in the 2nd axis of the plane for correcting in WO
Starting angle from the positive direction of the 1st axis of the plane to the reference edge of
the workpiece in the MCS (+-270 degrees)
Angle between workpiece reference edges when measuring a non-right-angled corner
Infeed amount at the measuring height for each measuring point for active protection zone
(see S_MVAR).
5)
4)
3)
4)
3)
4)
3)
4)
4)
4)
Programming Manual, 12/2019, 6FC5398-2EP40-0BA0
2)
4)
4)
NC programming
7)