ProControl 1KE
1KE Plus
ProControl
ProControl
1KE
The numbered columns in the following
table correspond to the numbered steps in
ProControl 1KE Plus Selection Guide, page 6
1 1 1
ProControl
ProControl
ProControl Application
Application
Application
Control Requirement
Requirement
Control
Control
Requirement
ADCM w/software and
bracket only
Flow Monitor (ADCM
w/G3000 and 5 ft
(1.5 m) cable, no
fluid panel)
Flow Monitor with
open setpoint fluid
pressure control
(includes fluid panel
and I/P to operate fluid
pressure regulator)
Gun Atomizing Air
Control
Closed Loop Fluid
Pressure Control
Closed Loop Fluid
Pressure or Fluid
Flow Control
Closed Loop Fluid
Pressure/Flow + Gun
Atomizing Air Control
✔ = Included
— = Not included. However, the system will
accommodate a user-supplied component.
* * * A Graco G3000 high-pressure meter (289813) is
used in models sold with a fluid flow meter. If you
intend to supply your own fluid flow meter, order a
model without a checkmark below. Make sure the
fluid flow meter is appropriate for fluid compatibility,
viscosity, flow rate range, etc.
** ** ** A Graco 1:1 low-flow air-operated regulator
(24C375) is used in models sold with a fluid regulator.
If you intend to supply your own air-operated fluid
3A6948A
Plus Model
Model Selection
Selection Matrix
Plus
Model
Selection
Component Selection
Component
Component
2 2 2
Fluid
Fluid
Fluid Flow
Flow
Flow
Meter*
Regulator**
Meter*
Meter*
Regulator**
Regulator**
N/A
✔
✔
✔
—
—
N/A
N/A
N/A
✔
✔
—
—
✔
✔
—
—
Matrix
Matrix
Power supply modules are discussed in
Power Supply Selection Guide, page 7
.
Selection Matrix
Matrix
Selection
Matrix
3 3 3
(included)
(included)
(included)
Fluid
Fluid
Fluid
Pressure
Pressure
Pressure
Transducer***
Transducer***
Transducer***
N/A
N/A
N/A
N/A
✔
N/A
—
N/A
N/A
✔
—
N/A
N/A
N/A
✔
✔
—
✔
✔
✔
—
✔
✔
✔
—
✔
✔
✔
—
✔
✔
✔
—
✔
regulator, order a model without a checkmark below.
Make sure the fluid regulator is appropriate for fluid
pressure range, material compatibility, viscosity, flow
rate range, etc. (Note:
regulator outlet must be a minimum of 10 psi (0.7
bar).)
***
***
*** All models intended for use with a pressure
transducer come with a low-pressure 100 psi (6.9
bar) transducer.
****
****
**** For managing fluid and atomizing air control. The
number below indicates the quantity included.
ProControl 1KE Plus Models
.
(included)
(included)
(included)
Current- - - to to to- - -
Current
Current
ProControl 1KE
ProControl
ProControl
Pressure I/P
I/P
Plus System
Pressure
Pressure
I/P
Plus
Plus
Transducer****
Transducer****
Transducer****
N/A
N/A
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
Note: Back pressure at the fluid
Note:
4 4 4
1KE
1KE
System
System
Models
Models
Models
25B283
25B284
25B285
25B286
25B287
25B288
25B289
25B290
25B291
25B292
25B293
25B294
25B295
25B296
25B297
25B298
25B299
5