Table of Contents
Advertisement
4. SET UP PROCESS OF A SOLARIS LD DISPLAY
About this chapter
This chapter describes roughly the installation process of the Solaris LD display per mounting configuration. The same processes
are valid for the different sizes and resolutions of the Solaris LD models. Several process stages refer to one or more of the detailed
"Installation procedures", page 23.
Overview
•
Set up process of a freestanding Solaris LD display
•
Set up process of a wall mounted Solaris LD display
•
Set up process of a hanging Solaris LD display
W
ARNING
display. Ensure you read, understand and follow all safety instructions mentioned in the chapter "Safety",
page 3 of this installation manual. Furthermore, be sure that all installation requirements for your Solaris LD
display are fulfilled, see "Installation requirements", page 7.
4.1 Set up process of a freestanding Solaris LD display
Set up process:
1. The first stage in the process is the installation of the Solaris LD feet. See procedure "Installation of the Solaris LD feet", page
23. Do not fasten the feet with the floor yet, just loosely attach. The feet must be tightly secured after the support structure
is installed upon the feet.
2. The second stage is the installation of the support structure. The framework of the support structure needs to be mounted upon
the previous installed Solaris LD feet. See installation procedure "Installation of the support frame upon the Solaris LD feet",
page 25. Together with the Solaris LD feet the support structure forms a solid backbone to support the other components of
the Solaris LD display.
3. The third stage in the process is the installation of the vertical precision frames upon the support structure. First the precision
frame in the middle of the support structure needs to be placed and then the neighboring frames. Note that the top and bottom
tiles have to be installed simultaneously with the neighboring frames because those tiles function as a caliber between the
frames. See chapter "Installation of the precision frames upon the Solaris LD support structure", page 34.
4. The next stage in the process is the installation of the peripherals as there are the mono phase power box and the Solaris D2
digitizer. Both peripherals must be installed at the same side of the display, recommended the right side when facing the
front of the display. See procedures "Installation of the mono phase power box", page 41, and "Installation of the Solaris D2
digitizer", page 42, for correct installation of the peripherals. Note that the digitizer can also be installed in a rack separated
from the display. In that case you can postpone the installation of the digitizer.
5. The next stage in the installation process is to fill up the Solaris LD display with tiles and realize the power and data cabling of
the tiles. See procedure "Installation of all the Solaris LD tiles with back access to the display", page 44.
6. In case the Solaris D2 digitizer is not installed inside the display housing the digitizer must be installed in a rack now. Do not
forget to realize the source cabling on the input module(s) of the Solaris D2 digitizer. See chapter "Cabling diagrams of the
Solaris LD display", page 59.
7. In this stage the finishing touch can be applied to the Solaris LD display. This is done by framing the extremities of the display
by closing up the sides and the rear of the display using cladding parts. Cladding must be placed following next sequence:
a) "Installation of the top- , bottom- and side-cladding support brackets", page 49.
b) "Installation of the top and bottom cladding", page 50.
c) "Installation of the left and right side cladding", page 53.
d) "Installation of the rear cladding", page 54.
e) "Installation of the foot cladding", page 56.
8. The second last stage in the process is the installation of the Solaris LD software on the local PC. Refer to the "User guide" of
the Solaris LD software for installation instructions.
9. Finally the Solaris LD system is ready to start up. After energizing the Solaris LD display and the Solaris D2 digitizer, the system
can be controlled and content scheduled with the Solaris LD software. Refer to the "User guide" of the Solaris LD software
for more information on how to schedule content for the Solaris LD display.
R5976773 SOLARIS LD DISPLAY 02/12/2004
:
Safety first. Fence off the installation area before start to unpack and assemble your Solaris LD
4. Set up process of a Solaris LD display
19
Advertisement
Table of Contents
