Agilent Technologies InfiniiVision 5000 Series Programmer's Manual page 712

Index
screen area for hardcopy print, 233
screen area for saved image, 306
screen data, 197
SECAM, 423, 427
seconds per division, 349
SEGMented commands, 491
segments, count of waveform, 461
segments, setting number of memory,
segments, setting the index, 162
segments, time tag, 462
select measurement channel, 279
self-test, 114
sensing a channel probe, 509
sensing a external trigger probe,
sensitivity of oscilloscope input, 185
sequence triggering, 354
sequential commands, 605
serial clock, 400, 419
serial data, 401, 420
serial decode bus, 317
serial decode bus display, 323
serial decode mode, 326
serial frame, 421
serial number, 147
service request, 112
Service Request Enable Register (SRE), 110,
560
set, 105
set center frequency, 217
set conditions, 120
set cursors, 529, 530
set date, 335
set delay, 120
set thresholds, 120
set time, 342
set time/div, 120
set up oscilloscope, 29
setting display, 218
setting external trigger level, 204
setting impedance for channels,
setting inversion for channels, 182
settings, 104, 108
settings, instrument, 231
setup, 154, 176, 194, 216, 231,
SETup commands, 491
setup configuration, 104, 108, 340
setup defaults, 105
setup memory, 104
setup reported, 354
setup, recall, 301
setup, save, 312
short form, 3, 588
show channel labels, 199
show measurements, 257, 278
SICL example in C, 608
SICL example in Visual Basic, 617
SICL examples, 608
SIGNal commands, 491
signal type, 188, 210
simple command headers, 589
single acquisition, 148
single-ended signal type, 188, 210
712
single-shot DUT, synchronizing with,
skew, 187, 507
slope, 386, 414
slope (direction) of waveform,
SLOPe commands,
slope not valid in TV trigger mode,
slope parameter for delay measurement,
161 software version,
source, 202, 216, 279, 373, 409,
SOURce commands,
source for function, 227, 228,
source for trigger,
source for TV trigger,
513 SOURce1 commands,
SOURce2 commands,
span, 216
span of frequency on display,
specify measurement,
SPI, 414, 415,
SPI commands,
SPI decode word width,
SPI trigger, 416,
SPI trigger clock,
SPI trigger commands,
SPI trigger data,
SPI trigger frame,
square root math function,
SRE (Service Request Enable Register), 110,
560
SRQ (Service Request interrupt), 128,
STANdard commands,
standard deviation measured on
waveform,
Standard Event Status Enable Register
(ESE), 96,
Standard Event Status Register (ESR), 98,
standard for video,
standard, LIN,
start acquisition, 113, 126, 146,
181 start and stop edges,
STARt commands,
start cursor, 529
start measurement,
340 start print job,
start time, 394,
start time marker,
state memory,
state of instrument, 101,
status, 111, 149,
Status Byte Register (STB), 109, 111, 112,
STATus commands,
status data structure clear,
status registers,
status reporting,
STB (Status Byte Register), 109, 111, 112,
step size for frequency span,
stop, 126, 150
stop acquisition,
stop cursor, 530
stop displaying channel,
stop displaying math function,
stop displaying pod,
580
531
491
386
264
100
463
491
514
387
426
492
492
229
279
417
492
327
418
419
413
420
421
223
135
492
277
565
564
427
410
148
262
492
257
240
529
526
108
340
151
558
493
95
48
553
558
229
150
124
124
124
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
stop time, 394, 530
storage, 108
store instrument setup, 101, 108
store setup, 108
store waveforms to pixel memory,
storing calibration information, 169
string variables, 46
string variables, reading multiple query results
into, 47
string variables, reading query results into
multiple, 47
string, quoted ASCII, 86
subnet mask, 29
subsource, waveform source, 467
subsystem commands, 90, 602
subtract math function, 216, 223,
subtract math function as g(t) source,
sweep mode, trigger, 354, 364
sweep speed set to fast to measure fall
time, 267
sweep speed set to fast to measure rise
time, 276
switch disable, 338
switch, calibration protect, 172
sync break, LIN, 411
syntax elements, 85
syntax rules, program data, 590
syntax, optional terms, 85
syntax, program message, 587
SYSTem commands, 334
system commands, 335, 336, 337, 338, 340,
342
system commands introduction, 334
T
tdelta, 525
tedge, 281
telnet ports 5024 and 5025, 451
Telnet sockets, 49
temporary message, 336
TER (Trigger Event Register), 151,
test, self, 114
text, writing to display, 336
threshold voltage (lower) for
measurement, 523
threshold voltage (upper) for
measurement, 533
thresholds, 262, 526
thresholds used to measure period,
thresholds, how autoscale affects,
TIFF image format, 308
time base, 345, 346, 347, 348, 349,
time base commands introduction,
time base reset conditions, 105
time base window, 351, 352, 353
time between points, 525
time buckets, 156, 157
TIME commands, 493
time delay, 539
time delta, 525
time difference between data points,
134
463
219
561
272
120
539
343
471